Solomonakoo Posted February 10, 2015 Report Share Posted February 10, 2015 I bought a 10" sub and was told it was a lvl 2 sub, but they did not know if it was a 2 or 4 ohm. Is there anyway to tell? thanks in advance Quote Link to comment Share on other sites More sharing options...
MrSkippyJ Posted February 10, 2015 Report Share Posted February 10, 2015 DMM Quote F150: Stock 2019 Harley Road Glide: Amp: TM400Xad - 4 channel 400 watt Processor: DSR1 Fairing (Front) 6.5s -MMats PA601cx Lid (Rear) 6x9s - TMS69 Link to comment Share on other sites More sharing options...
Miguels Posted February 10, 2015 Report Share Posted February 10, 2015 have you tried asking it? only way is using a DMM Quote my logshttp://www.stevemead...-my-new-set-up/my blow through loghttp://www.stevemead...future-updates/ 96 ss http://www.stevemeadedesigns.com/board/topic/164094-96-impala-ss-build/ Link to comment Share on other sites More sharing options...
Solomonakoo Posted February 10, 2015 Author Report Share Posted February 10, 2015 have you tried asking it? only way is using a DMM unfortunately it didn't reply when I asked. Quote Link to comment Share on other sites More sharing options...
Solomonakoo Posted February 10, 2015 Author Report Share Posted February 10, 2015 thanks guys, I just didn't know if there were any special markings on the magnet or anything like that. Quote Link to comment Share on other sites More sharing options...
rockFord_Expedition Posted February 10, 2015 Report Share Posted February 10, 2015 Always test the coils on any new (to you) sub that you get. You know how to do this? Quote Old School/New School RF Build March 2015 SOTM Winner How to crimp large wire Link to comment Share on other sites More sharing options...
Solomonakoo Posted February 10, 2015 Author Report Share Posted February 10, 2015 Always test the coils on any new (to you) sub that you get. You know how to do this? place the probes on the negative and positive leads? Quote Link to comment Share on other sites More sharing options...
Miguels Posted February 10, 2015 Report Share Posted February 10, 2015 have you tried looking through the holes? sometimes they do mark the former Quote my logshttp://www.stevemead...-my-new-set-up/my blow through loghttp://www.stevemead...future-updates/ 96 ss http://www.stevemeadedesigns.com/board/topic/164094-96-impala-ss-build/ Link to comment Share on other sites More sharing options...
Miguels Posted February 10, 2015 Report Share Posted February 10, 2015 something like this Quote my logshttp://www.stevemead...-my-new-set-up/my blow through loghttp://www.stevemead...future-updates/ 96 ss http://www.stevemeadedesigns.com/board/topic/164094-96-impala-ss-build/ Link to comment Share on other sites More sharing options...
rockFord_Expedition Posted February 10, 2015 Report Share Posted February 10, 2015 Always test the coils on any new (to you) sub that you get. You know how to do this? place the probes on the negative and positive leads? Yeah it's pretty straight forward, just check the resistance of each coil. Most know how to do it but some do not. Since starting this thread was probably more work than just checking them, I was just making sure you were good to go. Quote Old School/New School RF Build March 2015 SOTM Winner How to crimp large wire Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.