Dj_Scarface Posted May 6, 2012 Report Share Posted May 6, 2012 Ok I seen a post like this somewhere but cant find it... Ok if I got this rout & get a blown dc lvl 4 m1 can I use a dc lvl 4 m2 recone kit?? If that works with no problems... Will that sub(s) cause any problems if I put it in a box with a all stock dc lvl 4 m2??? Quote Working on my 93' Ford Bronco rebuild:I have:pioneer AVH-P6500Infinity Reference 6032SI frontsInfinity Reference 6832CF Rears Crescendo CZ 6.5 kicks Crescendo 1100.4 (2) DC Audio LvL 4 M2's (1) Juicebox BlackcherryPiece together amps & wiringBout to get:Crescendo Amps Crescendo Mids Crescendo Tweets Sky High Car Audio Wire Rockford Fosgate 360.2 or .3 My Buildhttp://www.stevemeadedesigns.com/board/topic/97426-93-ford-bronco-rebuild-full-system-body-paint/ Link to comment Share on other sites More sharing options...
SojiaRaggs9000 Posted May 6, 2012 Report Share Posted May 6, 2012 You should beable to. But that doesn't mean its on the same level as a m2. They're not just better soft parts, the motors where completely redesigned. Quote * Eclipse CD3200 with PAC SWI-CAN2 and SW-ECL2 Steering Wheel Controls Interface* Pioneer D-Series Mids and Highs ( Fronts: TS-D1702C; Rears; TS-D1702R and Dash; TS-D1002R )* Rockford Fosgate PBR300X4 ( Mids and Highs Amp )* DC 3.5k with Dual Inputs; Custom Plexiglass Backing ( Sub Amp )* Rockford Fosgate Balanced Line Driver * One FULLY LOADED ~ 10" DC m2 XL* Custom Built Carpeted Ported Box Tuned to 32hz. Single Chamber With Volume of 1.44618³ ft ; 1.13216³ ft After Displacement* Custom Built Carpeted Trunk Wall with Added Fans for Amplifier Cooling* MechMan 240a High Output Alternator * KnuKonceptz Krystal Kable RCA Cables* Upgraded Electrical With 1/0 KnuKonceptz Kolossus Fleks Kable and 1/0 Sky High Car Audio Cable* Five Exide Orbital ORB34M Marine 12 Volt Batteries* PowerMaster XS D3100 12 Volt Battery My 2008 Chrysler 300 Limited - SuperCharged 3.5L V6 - UBL My Old 2005 Ford Taurus - CarDomain - Vehicle Was Sold Link to comment Share on other sites More sharing options...
FroznBeavrBALLs Posted May 6, 2012 Report Share Posted May 6, 2012 i have 2 m1 lvl 4 motor/ baskets with m2 recones. they run great. its the same just upgraded to the flat wound coil. rms is around 1000 to 1100 i think... but dont quote me on that. Quote 2 DC 12" lvl 4s 1 DC 1.2k XS Power S3400 big 3 Alll KNU wire Pioneer HU cheapo Legacy coaxes (just for now) http://www.stevemead...n-sentra-build/ Link to comment Share on other sites More sharing options...
Dj_Scarface Posted May 6, 2012 Author Report Share Posted May 6, 2012 You should beable to. But that doesn't mean its on the same level as a m2. They're not just better soft parts, the motors where completely redesigned. I know there not the same, they can all handle the same watts but if i put them in the same box will it cause problems or noticeable audio Quote Working on my 93' Ford Bronco rebuild:I have:pioneer AVH-P6500Infinity Reference 6032SI frontsInfinity Reference 6832CF Rears Crescendo CZ 6.5 kicks Crescendo 1100.4 (2) DC Audio LvL 4 M2's (1) Juicebox BlackcherryPiece together amps & wiringBout to get:Crescendo Amps Crescendo Mids Crescendo Tweets Sky High Car Audio Wire Rockford Fosgate 360.2 or .3 My Buildhttp://www.stevemeadedesigns.com/board/topic/97426-93-ford-bronco-rebuild-full-system-body-paint/ Link to comment Share on other sites More sharing options...
CJ18 Posted May 6, 2012 Report Share Posted May 6, 2012 I wOuld definitely recommend gettin the new level 4 recone. The new 4 coil is a flat wound coil. The old level 4 coil is now used in the level 3. Quote Link to comment Share on other sites More sharing options...
Dj_Scarface Posted May 6, 2012 Author Report Share Posted May 6, 2012 i have 2 m1 lvl 4 motor/ baskets with m2 recones. they run great. its the same just upgraded to the flat wound coil. rms is around 1000 to 1100 i think... but dont quote me on that. Good to know... Not I can get the blown m1 lvl 4 motor/ baskets for the extra low. Still need to see if putting them both in the same box will cause problems... Quote Working on my 93' Ford Bronco rebuild:I have:pioneer AVH-P6500Infinity Reference 6032SI frontsInfinity Reference 6832CF Rears Crescendo CZ 6.5 kicks Crescendo 1100.4 (2) DC Audio LvL 4 M2's (1) Juicebox BlackcherryPiece together amps & wiringBout to get:Crescendo Amps Crescendo Mids Crescendo Tweets Sky High Car Audio Wire Rockford Fosgate 360.2 or .3 My Buildhttp://www.stevemeadedesigns.com/board/topic/97426-93-ford-bronco-rebuild-full-system-body-paint/ Link to comment Share on other sites More sharing options...
FroznBeavrBALLs Posted May 6, 2012 Report Share Posted May 6, 2012 well you can put them or it in the same box as before and be fine... if thats what you mean... ... BUT DONT put a full m2 lvl 4 in the same box WITH a sub with an m1 motor and m2 recone. Quote 2 DC 12" lvl 4s 1 DC 1.2k XS Power S3400 big 3 Alll KNU wire Pioneer HU cheapo Legacy coaxes (just for now) http://www.stevemead...n-sentra-build/ Link to comment Share on other sites More sharing options...
Dj_Scarface Posted May 6, 2012 Author Report Share Posted May 6, 2012 I wOuld definitely recommend gettin the new level 4 recone. The new 4 coil is a flat wound coil. The old level 4 coil is now used in the level 3. KOOL!! Will two m1 lvl 4 with m2 soft parts cause any problems or noticeable audio difference if I put them in a box with two all stock dc lvl 4 m2??? Quote Working on my 93' Ford Bronco rebuild:I have:pioneer AVH-P6500Infinity Reference 6032SI frontsInfinity Reference 6832CF Rears Crescendo CZ 6.5 kicks Crescendo 1100.4 (2) DC Audio LvL 4 M2's (1) Juicebox BlackcherryPiece together amps & wiringBout to get:Crescendo Amps Crescendo Mids Crescendo Tweets Sky High Car Audio Wire Rockford Fosgate 360.2 or .3 My Buildhttp://www.stevemeadedesigns.com/board/topic/97426-93-ford-bronco-rebuild-full-system-body-paint/ Link to comment Share on other sites More sharing options...
CJ18 Posted May 6, 2012 Report Share Posted May 6, 2012 I wOuld definitely recommend gettin the new level 4 recone. The new 4 coil is a flat wound coil. The old level 4 coil is now used in the level 3. KOOL!! Will two m1 lvl 4 with m2 soft parts cause any problems or noticeable audio difference if I put them in a box with two all stock dc lvl 4 m2??? No DO NOT do that. They will act differently. Quote Link to comment Share on other sites More sharing options...
Dj_Scarface Posted May 6, 2012 Author Report Share Posted May 6, 2012 I wOuld definitely recommend gettin the new level 4 recone. The new 4 coil is a flat wound coil. The old level 4 coil is now used in the level 3. KOOL!! Will two m1 lvl 4 with m2 soft parts cause any problems or noticeable audio difference if I put them in a box with two all stock dc lvl 4 m2??? No DO NOT do that. They will act differently. Well there goes that plan Quote Working on my 93' Ford Bronco rebuild:I have:pioneer AVH-P6500Infinity Reference 6032SI frontsInfinity Reference 6832CF Rears Crescendo CZ 6.5 kicks Crescendo 1100.4 (2) DC Audio LvL 4 M2's (1) Juicebox BlackcherryPiece together amps & wiringBout to get:Crescendo Amps Crescendo Mids Crescendo Tweets Sky High Car Audio Wire Rockford Fosgate 360.2 or .3 My Buildhttp://www.stevemeadedesigns.com/board/topic/97426-93-ford-bronco-rebuild-full-system-body-paint/ Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.