hdorre Posted February 7, 2015 Report Share Posted February 7, 2015 ohh myyy Quote On 5/8/2011 at 7:38 PM, Kranny said: On 5/8/2011 at 7:35 PM, 'Maxim' said: It hurts me inside when I read stuff like this and remember you're 15 LMFAO so true Mitsubishi 3000GT (Old Build) Headunit: Pioneer 80PRS Frontstage: (2) McLaren Audio MLT-2 Tweeters & (4) PRV Audio MR Series Neo 6.5" Mids Substage: 4 15" Hybrid Subs - Tantric Motors & Sundown Softies Amps: Banda 2.4D Amp (Tweets), American Bass VFL 350.4 (Mids), and (2) Ampere 3800s Electrical :Singer 260A Alt & JY Power Lithium 2005 Chevy Colorado Ext Cab Headunit: Pioneer 80PRS Frontstage: 4 PRV 700Ti Tweets & 6 10" Delta Mids on 3000wrms Substage: 6 Fi BTL 18s in a 4th Order Walkthrough on 3 Wolfram 4500s Electrical: Singer "390" and JY Power My Official Feedback Thread Link to comment Share on other sites More sharing options...
audiofanaticz Posted March 14, 2015 Author Report Share Posted March 14, 2015 Time to rip out this temporary wiring job. I had some major feedback, not alternator or engine noise. It was there with the truck off completely. Most likely it was caused by cheap rca's with zero shielding being ran over and under numerous power wires, and or the 360.2 just sitting on top of the 4channel. LOL 2 Quote Link to comment Share on other sites More sharing options...
im45pl Posted March 14, 2015 Report Share Posted March 14, 2015 (edited) I always get excited when I see this pop up Edited March 14, 2015 by im45pl 1 Quote TEAM DC AUSTRALIA My_Build_Log Link to comment Share on other sites More sharing options...
audiofanaticz Posted March 15, 2015 Author Report Share Posted March 15, 2015 So I bought a welder the other day, and went to use it last night and the feed wheel didnt spin. So I returned it last night which is where I left off after cutting the angle iron. Today I decided to try welding, this time the feed wheel works. I need a bottle and some gas on it, but Im going without for now. Not a pro at welding by any means, and all I ever did was a little bit of welding with a stick welder. I got a big learning curve ahead of me. After all people took classes for this and have many years experience. So here is my first weld... LOL and amazingly it stays together! haha grinding it all smooth test fitting more test fitting some added corner supports to stiffing it up a little I need to get a little more steel, I want to run a lip or a small raised edge along the bottom so the amps will not slide off when i set them on there before I get to put the bolts through to securely hold them. 2 Quote Link to comment Share on other sites More sharing options...
Borris The Blade Posted March 15, 2015 Report Share Posted March 15, 2015 See you found a way to get all 4 to fit back there. Welds look much better after grinding them down lol, I'm sure mine would look much worse. 1 Quote It's like rubbing your wiener up against a sheep. Link to comment Share on other sites More sharing options...
audiofanaticz Posted March 17, 2015 Author Report Share Posted March 17, 2015 Little more progress.. Welded the little strip on the bottom to give the amp rack a ledge to set the amps on so they dont slide off before they get bolted. welds are starting to look a tad better, but much more prat ice is needed for sure! The hinge idea I came up with. Using a grade 8 bolt so it should be plenty strong and welded the nut to the amp rack itself. Should give me minimal /limited room to get under the amps for whatever reason if needed. Hung the rack from a JL audio basket with a giant ziptie And a couple coats of paint Sold an alt to my friend and needed a harness to get the dummy light to turn off on the dash, Singer was the first to reply and reasonably priced ftw amps laid out on the rack to mark the holes to drill them for bolts Also drilled the holes in the angle iron which will be secured to the back of the wall with lag bolts Hinges bolted on Also pulled the batteries out the back for the time being 4 Quote Link to comment Share on other sites More sharing options...
audiofanaticz Posted March 21, 2015 Author Report Share Posted March 21, 2015 Figure I do the easy update.. All 4 4500s are in... 4 Quote Link to comment Share on other sites More sharing options...
magillaru Posted March 21, 2015 Report Share Posted March 21, 2015 Can't wait to see this playing......I get excited every time I see an update. Quote Singer Alternators Team Asshole #anothershittysingerbuild Link to comment Share on other sites More sharing options...
audiofanaticz Posted March 21, 2015 Author Report Share Posted March 21, 2015 If I backed it into my garage to get out of the rain I could have it playing in not long at all, but Im sore from all the crap I did today. Amps just need to be tuned, and have woofers hooked to them. 2 Quote Link to comment Share on other sites More sharing options...
moredbs Posted March 21, 2015 Report Share Posted March 21, 2015 (edited) I love looking at your work! Top notch! Edited March 21, 2015 by moredbsplease 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.