MatthewBigBossWilliams Posted November 15, 2014 Report Share Posted November 15, 2014 I have issues with my CC. Whenever I turn the signal down on my amps, the red light never goes away. even when the radio is down and amps are down. am I doing something wrong? Quote Link to comment Share on other sites More sharing options...
Kyblack76 Posted November 15, 2014 Report Share Posted November 15, 2014 What are you trying to even do with it? Set a pass or what? what track? what freq? what amp? what drivers/speakers ? Yes, ill say now, YOUR DOING IT WRONG. Read the instructions you got with it. Quote SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
MatthewBigBossWilliams Posted November 15, 2014 Author Report Share Posted November 15, 2014 What are you trying to even do with it? Set a pass or what? what track? what freq? what amp? what drivers/speakers ? Yes, ill say now, YOUR DOING IT WRONG. Read the instructions you got with it. I was trying to set two cresendo s1500 gain together. i am not trying to set the crossovers the same since the box is tuned dumb low. its an FI SP4 15in and I do believe it was track 10 that the instructions told me to use. I re read the instructions. plugged out the connectors on the CC before turning it on. turned it on then then calibrated it. as soon as i connect the negative to the ground then the positive, the signal is red. Quote Link to comment Share on other sites More sharing options...
Kyblack76 Posted November 15, 2014 Report Share Posted November 15, 2014 (edited) turn the main vol down some... did you "set" it in the correct mode? Edited November 15, 2014 by KyLar96 Quote SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
Kyblack76 Posted November 15, 2014 Report Share Posted November 15, 2014 This procedure requires the CC-1 to be placed in a special mode reserved for SPL competitors and audiophiles. 1. Switch the CC-1 off by holding the OFF button for 1 second. (This must be done to initalize the program mode) Now switch CC-1 power on by pressing the ON button. 2. Disconnect the harness to make sure there is no signal being applied to the CC-1 and that the Signal LED is NOT illuminated. 3. Press and hold the READ button for 3-5 seconds or until the Set LEDs start flashing. Release Set button. CC-1 is now in competition mode!! 4. Next you need to connect the CC-1 to the “Master” amplifier’s outputs. Use the included harness to connect to amplifier’s outputs; Red to speaker (+) and Black to battery ground. 12 5. Set the source unit’s volume to zero. Select the track on the CD that corresponds to the desired frequency you wish to match gains at. If you don’t know which frequency to use try 40 Hz (track 10 Disc A) if it is a subwoofer amplifier, or 1 kHz (track 8 Disc if it is a full range amplifier. Play track on repeat. 6. Continue by turning up the source unit volume until you see the Signal LED illuminate green. If the LED turns red, this indicates the volume is too high. Turn volume down until LED remains green. 7. When Signal LED remains Green, press the READ button. The Blue Calibrated LED should illuminate. 8. Now without touching any adjustments on anything, connect the CC-1 to the output of the next amplifier that you wish to match it’s gain to the first amplifier. 9. The LEDs will indicate if the gain is too high or too low compared to the “Master” amplifier. 10. Adjust gain on the amplifier that the CC-1 is now connected to until the Calibrated LED illuminates. The amplifier’s gain is now matched to the Master amplifier’s gain within +/- 0.05dB !! Quote SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
Kyblack76 Posted November 15, 2014 Report Share Posted November 15, 2014 (edited) I have issues with my CC. Whenever I turn the signal down on my amps, the red light never goes away. even when the radio is down and amps are down. am I doing something wrong? What do you mean Whenever I turn the signal down on my amps,? and signal meaning the cross over? or the gain adjustment. ??? Your master should be set clean. You then use the cc1 to MATCH the second one to the one you wanna mirror. Please, when asking for tech help with the tools, you need to use your words proper for correct help. You should ONLY be touch the gain on the slave amp..... The master should be set CLEAN , and then with the CC1 per instructions you will READ the master. THen move to the slave, setting it to mirror the master using ITS gain only. Edited November 15, 2014 by KyLar96 Quote SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
MatthewBigBossWilliams Posted November 15, 2014 Author Report Share Posted November 15, 2014 I have issues with my CC. Whenever I turn the signal down on my amps, the red light never goes away. even when the radio is down and amps are down. am I doing something wrong? What do you mean Whenever I turn the signal down on my amps,? and signal meaning the cross over? or the gain adjustment. ??? Your master should be set clean. You then use the cc1 to MATCH the second one to the one you wanna mirror. Please, when asking for tech help with the tools, you need to use your words proper for correct help. You should ONLY be touch the gain on the slave amp..... The master should be set CLEAN , and then with the CC1 per instructions you will READ the master. THen move to the slave, setting it to mirror the master using ITS gain only. Thats the thing, I did those instructions before and even turned the radio signal down. I turned the volume gain down and didnt even get around to touching the crossovers. Quote Link to comment Share on other sites More sharing options...
Kyblack76 Posted November 15, 2014 Report Share Posted November 15, 2014 So your master has been set clean, correct? Quote SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
MatthewBigBossWilliams Posted November 15, 2014 Author Report Share Posted November 15, 2014 Yes. I set that first, did my door speakers then moved my way to the amps. Quote Link to comment Share on other sites More sharing options...
Kyblack76 Posted November 15, 2014 Report Share Posted November 15, 2014 (edited) Yes. I set that first, did my door speakers then moved my way to the amps. dude.. when i say master, that means your amps...one of the 2 sub amps. that is what your trying to gain match right? Edited November 15, 2014 by KyLar96 Quote SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.