Bayuk89 Posted August 20, 2016 Report Share Posted August 20, 2016 So i have an audison SR2 amp, there is full pass and high pass (mine is set on high pass) and there is a x1 or x10 setting for the slope ? Can anyone please help me understand the difference in x1 and x10...... its always been set at x1 since its been installed, just curious to what happens when you slide it to x10 Link to comment Share on other sites More sharing options...
ToNasty Posted August 20, 2016 Report Share Posted August 20, 2016 That's for the hpf. What is it running ***Super Sellers List***http://www.stevemeadedesigns.com/board/topic/25829-super-sellers-buyers Link to comment Share on other sites More sharing options...
Bayuk89 Posted August 20, 2016 Author Report Share Posted August 20, 2016 Just some cheap $80 RF 6x9's high pass filter is sext to 85 hz on the dial.... there is a switch ( x1 ) and ( x10 ) in the picture shown.... i dont know what those settings mean, if you look at all the circled items it tells you what changes (on the graph) between the two setting but I dont know what it means lol Link to comment Share on other sites More sharing options...
Bayuk89 Posted August 20, 2016 Author Report Share Posted August 20, 2016 See the range switch X1 and X10 ( in purple ) and the differences in the switches ( in red ) what does those charts mean or can someone explain what changes when switching from x1 to x10 Link to comment Share on other sites More sharing options...
ToNasty Posted August 21, 2016 Report Share Posted August 21, 2016 It means x1 or x10. Like 5 x 5 =25. Multiplication ***Super Sellers List***http://www.stevemeadedesigns.com/board/topic/25829-super-sellers-buyers Link to comment Share on other sites More sharing options...
MrSkippyJ Posted August 21, 2016 Report Share Posted August 21, 2016 it changes the frequencies of the crossover. at x1 the frequencies are as written on the amp, at x10 you multiply the numbers on the amp by 10. F150: Stock 2019 Harley Road Glide: Amp: TM400Xad - 4 channel 400 watt Processor: DSR1 Fairing (Front) 6.5s -MMats PA601cx Lid (Rear) 6x9s - TMS69 Link to comment Share on other sites More sharing options...
ToNasty Posted August 21, 2016 Report Share Posted August 21, 2016 So if you have the filter set to 250hz. And the x10 is selected. It's actuslly at 2500hz ***Super Sellers List***http://www.stevemeadedesigns.com/board/topic/25829-super-sellers-buyers Link to comment Share on other sites More sharing options...
Bayuk89 Posted August 21, 2016 Author Report Share Posted August 21, 2016 Ahhh thanks guys lol for the life of me i couldnt figure it out. I will have to leave it at 85 hz x1 then. Link to comment Share on other sites More sharing options...
Bayuk89 Posted August 21, 2016 Author Report Share Posted August 21, 2016 I have a Audison SR4 (4ch) in my closet, couldnt i just install the SR4 to power my midrange drivers (when i buy them) and have my SR2 (2ch) power my tweeters ? If i can set the frequency all the way up to 5k then i wouldnt need an external cross over because the amp has an high adjustable cross over. Link to comment Share on other sites More sharing options...
ToNasty Posted August 21, 2016 Report Share Posted August 21, 2016 Why not just use the 4ch to run the mids and tweets instead of 2 amps ***Super Sellers List***http://www.stevemeadedesigns.com/board/topic/25829-super-sellers-buyers Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.