Jump to content
the_garynator

Project Flexington: 157.6db @ 37hz Parallel 6th order walk through, DC Neo Elite 18s, 4 DC 5.0ks, JY Lithium, 12 banks of XS Caps

Recommended Posts

the_garynator    451

So to catch up on pictures, here's where I mounted the subs to the removable baffles.

I used 1/4" bolts with nylon lock washers but was worried the points might tear the surround:

20161002_021845_zpsze3zuux2.jpg

So I ground down 2 of the points, since the heads just fit in the basket, all I had to do to keep them from spinning as I tightened the nuts was apply a bit of pressure with my finger.

20161002_023228_zpsgatp3cp8.jpg

Here's a sub mounted in the removable baffle

20161002_023430_zpsnoukzuqq.jpg

Subs mounted, gotta say my removable baffle system was worth the time and work, almost no effort to load the subs. It was great!!!!

20161002_030204_zpsd0hm1dnc.jpg

Crimped some ends, the kolossus fleks 4/0 is massive

20161002_135322_zps5jaalurx.jpg

Got wire?

20161002_145426_zpsrmege2sz.jpg

Warhorse mounted. Made a temporary buss bar to tide me over until I get my projectdb ones.

20161002_145538_zpsk3elxi27.jpg

Managed to get 4 runs of 1/0 from front to back and one nsb170ft installed. Definitely can tell it will get much louder once I get more electrical installed!

Awsome build. I'm taking notes on your box, I love it. Are those 10s SVC? Where will you cross them over at if you don't mind me asking?

Thanks man! I'm not sure what it am going to cross them over at. I'm planning on getting a dsp in the near future with active crossovers and adjust. And yes they're svc.

On that note, I ordered the DC 175.4 that will be powering the 10s!

  • Like 1

Share this post


Link to post
Share on other sites
kryptonite    354

Damn awesome build dude!!!! Makes me miss my walk through build I started in my ranger even more, can't wait to see this finished and playing!!!

  • Like 1

Share this post


Link to post
Share on other sites
Mr DeeBeez    647

I wanna get a demo some day! Dont know if there are any more meets this year tho :/ Wish I could have made it to Fond du Lac last weekend.

Cant wait to see it all done! Looks great!

Share this post


Link to post
Share on other sites
the_garynator    451

Thanks guys! Definitely down to demo, it's what I am building it for, just hit me up, my schedule is pretty flexible.

Sealed off the wall tonight and now I'm crimping lugs on more runs of 1/0. I think I've decided to run dedicated grounds instead of using the frame but going to have to wait for another 100ft of black shca 1/0 to get here. Other than that I just need buss bars and hardware for my caps then electrical will be complete :)

  • Like 2

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By WalledSonic
      The purpose of this thread is to evaluate and discuss the internal resistance of various batteries and (possibly?) test methods.
      I’ll start this off by using the DC Load method to test some XS AGM, some K2 73Ah cells, and some K2/JYP 80Ah cells.  The DC load method was used because that’s all the equipment that I had available or was able to purchase quickly and on the cheap.  Here’s a link for more information on Load Test Methods.
      http://batteryuniversity.com/learn/article/how_to_measure_internal_resistance
      Calculation used was Rint = ((Vrest/Vload) -1) x Rload)
      Where
      Rint = internal resistance
      Vrest = Voltage at rest
      Vload = Voltage once load is applied
      Rload = resistance of the load resistor
      Now onto some pictures of the setup.  If there is something amiss please chime in so we can figure it out.
      1ohm load resistors (although they test out at 0.9ohm)

      I connected them in series on one end, and I can change the resistance by simply connecting my jumper wire differently. I have the opportunity to connect at 0.45ohm, 0.9ohm, and 1.8ohm.  Here's proof of half(ish) ohm, although I didnt use this low of a resistance for data collection:

      So this connection would be 1.8ohm

      This connection would be 0.9ohm

      Here's the 73Ah K2 cells (not JY collaboration batteries)

      The day before testing, I topped off all the batteries, including the JYP's in the back and the AGMs to the right. 

      24 hours later, I actually took measurements.

      Data for the lithiums:

      Data for the D3400R AGM

      Looking forward to some comments, suggestions, etc.  Thanks for looking!
    • By WalledSonic
      Its time to refresh this build log!  Been a busy summer with Slam, Heatwave, Photobucket took a sh*t, sold my other car, etc etc.
      Here's some pics from the last build log, since the PB pics arent visible anymore:


      Cant fit more tire in this car.  Bass squat.

      But that flush tho

      Roll bar

       
    • By Krupske
      So...
       
      The plans have changed a little bit, no wall but two 12's now
      The reason for making this new thread.
       
      Old thread  https://www.stevemeadedesigns.com/board/topic/205731-my-first-audio-build/
       
       
      The car

       

       

       

       

       

       

       

       

       

       

       

       

       
      Still a lot more to deaden!
      Btw i've used Silent Coat and STP ak04 premium
       
       
       
      So the new plan(setup) will be as following:
       
      HU: ?? don't know yet
      Subs: 2 Phoenix Gold Elite.12D4
      Subs Amp: Rockford Fosgate Power T2500.1
      Mids and Highs: Phoenix Gold Elite.65CS Components
      Mids and Highs Amp: Rockford Fosgate Power T400.2
      Electrical:
      Ground Zero GZBP 12.3500X battery under the hood
      XS Power XE 12-110 battery in the back
      180 Amp Alternator
      OFC 0 awg power/ground/big 3
      OFC 4 awg power/ground
      OFC 8 awg subwoofer wire
      OFC 10 awg speaker wire
      Rockford Fosgate Fuses
      Rockford Fosgate Fuseholders 6x
      Rockford Fosgate RCA’s 10feet 2x
      Rockford Fosgate PEQ remote controller
      Some dual inputs
      Stinger voltmeter
       
       
      Some parts

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       
       
      I'm now waiting on the 0awg and 10awg OFC wire to come thru the mail, then its all complete..
       
      Box is finished just need to wrap it.
      Thanks to JOE X for the box design!!
      It's for 2 zv4 12's but i'm hoping it will work fine with the Elite.12's
       
       
      You'll be hearing from me soon, as soon as ive done some more work
       
       
    • By dylan117
      I've seen quite a few write-ups on 4th order ratios and what not, but am struggling to find anything on 6th orders. what would a 1:1 compared to a 2:1, 3:1, etc. ratio 6th order sound like? Thanks!
  • Who's Online   7 Members, 0 Anonymous, 556 Guests (See full list)