Red-navi-916 Posted May 2, 2018 Report Share Posted May 2, 2018 Apparently I’ve been out of this car audio world for too damn long because I’m stumped i have this amp with these specs and 4 of these speakers with these specs. how to wire it up diagram anyone? Thanks. BUILDLOG http://www.stevemeadedesigns.com/board/ind...showtopic=61862 "98crewcab"Never a POS....just always "a work in progress" lol that's how we roll bitches!!! Your a lowlife kid. I bet your mother wants to kill herself for not swallowing your ass. Link to comment Share on other sites More sharing options...
SkarredSierra Posted May 2, 2018 Report Share Posted May 2, 2018 I use this site when im checking wiring to confirm ohm load. https://www.the12volt.com/caraudio/woofer_configurations.asp Link to comment Share on other sites More sharing options...
AlpineNut Posted May 2, 2018 Report Share Posted May 2, 2018 Wire the amp into a 2ohm load for the channels but the only thing is you will either have Left or Right or Front or Rear only since it is only a 2 channel amp and it puts out 470W - 606Wx2 @ 2ohms per what the review says. http://content.arcaudio.com/pdfs/reviews/product-reviews/KS600.2.pdf 73456w9vbwevsdb sodtbsorutnvsd sdtuspdun sd d f gsdfiusd gdf n Link to comment Share on other sites More sharing options...
Red-navi-916 Posted May 2, 2018 Author Report Share Posted May 2, 2018 6 minutes ago, AlpineNut said: Wire the amp into a 2ohm load for the channels but the only thing is you will either have Left or Right or Front or Rear only since it is only a 2 channel amp and it puts out 470W - 606Wx2 @ 2ohms per what the review says. http://content.arcaudio.com/pdfs/reviews/product-reviews/KS600.2.pdf Yeah this amp was good with just these two speakers. But ended up adding 2 more of them so now I’m a predicament. And they are tower speakers. Thanks for the input guys. BUILDLOG http://www.stevemeadedesigns.com/board/ind...showtopic=61862 "98crewcab"Never a POS....just always "a work in progress" lol that's how we roll bitches!!! Your a lowlife kid. I bet your mother wants to kill herself for not swallowing your ass. Link to comment Share on other sites More sharing options...
Liquid Arthur Posted May 2, 2018 Report Share Posted May 2, 2018 I would shove the wires for both right speakers into the right channel output, do the same with the left speakers and the left output, and call it a day. This will result in a stereo 2 ohm load, which most amplifiers since the 90's can handle no problem. You'll have plenty of power to your speakers. I'd add though, don't run it very long when the boat's engine is not running. You need plenty of juice to keep this going. Link to comment Share on other sites More sharing options...
Red-navi-916 Posted May 4, 2018 Author Report Share Posted May 4, 2018 On 5/2/2018 at 3:23 PM, Liquid Arthur said: I would shove the wires for both right speakers into the right channel output, do the same with the left speakers and the left output, and call it a day. This will result in a stereo 2 ohm load, which most amplifiers since the 90's can handle no problem. You'll have plenty of power to your speakers. I'd add though, don't run it very long when the boat's engine is not running. You need plenty of juice to keep this going. Yeah. Copy that thanks. And I have three batteries and three amps as well. It’s been doing good for a while. Just adding two more of these wet sounds to the tower BUILDLOG http://www.stevemeadedesigns.com/board/ind...showtopic=61862 "98crewcab"Never a POS....just always "a work in progress" lol that's how we roll bitches!!! Your a lowlife kid. I bet your mother wants to kill herself for not swallowing your ass. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.