dimondntr2004 Posted June 7, 2018 Author Report Share Posted June 7, 2018 I have equipment and box built. just finished doors. I was trying to set what's needed to power the amps correctly . I already have a 320 alt and lithium80 ah. just wanted to know what else do I need to get. Link to comment Share on other sites More sharing options...
Crazy 8s Drums Posted June 7, 2018 Report Share Posted June 7, 2018 Have you done 'the big three'? With a 10kw+ system, you'll need to do that and more. You'll probably need to do 2 runs of 2/0 oxygen free cable to the lithium battery and then from there to a distribution block of some sort. You'll need fusing for all of it. A 10kw system ain't fukinn around and you want to do it right. Your 2 ga welding wire won't be doing it right and may be dangerous. Seriously, make a thread in the members build section so that others will know what you are trying to do . There are definitely folks here who know how to put together badass heavy hitting systems and they will talk to you about it. Orion XTR amplifiers Skar subs Link to comment Share on other sites More sharing options...
Ninja_v1.0 Posted June 7, 2018 Report Share Posted June 7, 2018 1) crazy8 is right 2) in order to hold 14+v on 2 5ks youre going to need more alt and a lot more of it 3) you going to need to up your wire as well.. especially with lithium as the current discharge is A LOT more than a normal battery.. i would suggest using a buss bur and coming off that lithium going to your amps. good luck Link to comment Share on other sites More sharing options...
dimondntr2004 Posted June 7, 2018 Author Report Share Posted June 7, 2018 thanks I liked atit and it's 2/0 gauge wire. I will get another 320 alt and exchange the 2/0 to 4/0 welding wire . then use distribution block to amps. just haven't figured out if the 80ah lithium will be snuff or more batteries Link to comment Share on other sites More sharing options...
dimondntr2004 Posted June 7, 2018 Author Report Share Posted June 7, 2018 big 3 done already. just need input to increase voltage. and have enuff battery for the system. Link to comment Share on other sites More sharing options...
Kyblack76 Posted June 7, 2018 Report Share Posted June 7, 2018 But, your not gonna pull any where near max amperage. Those dyno runs are full rip, BURPs on tones, and a REACTIVE load,..basically, worse case scenario You really really wanna hold 14v, . Charge at 16, and run 14v cells. Seems pointless to me, but, whatever peels your banana. Dropping some on voltage is not the end of the universe. It is a 12v board after all. I can see you already saying "but I want maximum power output" well, wiring at 1ohm nominal, you wont see that anyway. SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
Crazy 8s Drums Posted June 7, 2018 Report Share Posted June 7, 2018 11 minutes ago, dimondntr2004 said: big 3 done already. just need input to increase voltage. and have enuff battery for the system. If you did it with that 2 ga wire it isn't done yet. You'll need 1/0 minimum for that HO alt for power (fused at 350a) and ground, you'll need atleast as much total chassis-to-battery negative as you have in positive runs....so if you have 2x 2/0 ga (+) to the amps you'll need 2x 2/0 grounds from chassis to neg battery. Orion XTR amplifiers Skar subs Link to comment Share on other sites More sharing options...
Masterbasser Posted June 8, 2018 Report Share Posted June 8, 2018 if your tryna hold high voltage try a buncha maxwell ultracapacitors or add more alternators. Kenwood excelon ddx795 3 370 amp CES alternators (audio side only) McLaren dome tweeters Crescendo 6.5 ultra neos NVX JAD800.4 4 PA x4 SPL 18's 4 Digital Designs m5's at .7 ohms each 2 K2 80 ah lithiums 3 group 31 agms Ledglow million color (12 piece) 2007 Yukon xl Link to comment Share on other sites More sharing options...
josh weldon Posted May 21, 2019 Report Share Posted May 21, 2019 what battery setup would yall recomend for 1 17k or 2 5ksplx which would be a better setup? Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.