youdoofus Posted August 5, 2019 Report Share Posted August 5, 2019 im looking for a molex plug for my 2012 Altima SL Bose amp. Im wanting to reuse the factory wiring to the speakers as im not planning on using too much power, but i am replacing the speakers themselves, deck, rca's to the amps and so forth. I have a handle on the vast majority of it and will test each +- pair for continuance and so forth, id just like to be able to wire into the factory plug for the sake of simplicity. Any suggestions yall? Link to comment Share on other sites More sharing options...
Joshdashef Posted August 6, 2019 Report Share Posted August 6, 2019 Junkyard maybe ? Might take some work but you can snag a plug off a totaled one SMD Tool Map (2022): https://www.stevemeadedesigns.com/board/topic/220267-smd-tool-map-2022/ My Port Size Calculator (in progress): https://www.stevemeadedesigns.com/board/topic/217087-port-size-calculator-in-progress/ Common Port Walls for a Slot Port: https://www.stevemeadedesigns.com/board/topic/217076-common-port-walls-why-it-matters-to-your-box/?tab=comments#comment-3240313 Link to comment Share on other sites More sharing options...
youdoofus Posted August 6, 2019 Author Report Share Posted August 6, 2019 10 hours ago, Joshdashef said: Junkyard maybe ? Might take some work but you can snag a plug off a totaled one that was my original thought too. none of my local salvage yards has one (oddly enough) and theyre proving to be spendy for just the plug online. $80 minimum from what ive seen Link to comment Share on other sites More sharing options...
youdoofus Posted August 6, 2019 Author Report Share Posted August 6, 2019 All I think I really need is the opposite end of the plug pictured here. It looks incredibly similar to a regular wiring harness usually stuffed behind an aftermarket deck. Link to comment Share on other sites More sharing options...
Joshdashef Posted August 6, 2019 Report Share Posted August 6, 2019 Wait you have the plug right ? You should look into re pinning the molex plug SMD Tool Map (2022): https://www.stevemeadedesigns.com/board/topic/220267-smd-tool-map-2022/ My Port Size Calculator (in progress): https://www.stevemeadedesigns.com/board/topic/217087-port-size-calculator-in-progress/ Common Port Walls for a Slot Port: https://www.stevemeadedesigns.com/board/topic/217076-common-port-walls-why-it-matters-to-your-box/?tab=comments#comment-3240313 Link to comment Share on other sites More sharing options...
youdoofus Posted August 6, 2019 Author Report Share Posted August 6, 2019 14 minutes ago, Joshdashef said: Wait you have the plug right ? You should look into re pinning the molex plug yeah, i have the plug. im just trying to leave the stock one in the car. im totally fine with pinning a raw plug, just trying to find the end id need to do that. in the picture, the side with the wires goes back into the car to the stock speaker locations. Just trying to interface with that. Honestly, i guess all i really need to wire up is the front and rear doors, a total of 8 wires as the tweets and 6x9s will be rewired. Tweets are too big of a pita, and the 6x9s are... well.... right there Link to comment Share on other sites More sharing options...
reedal Posted August 6, 2019 Report Share Posted August 6, 2019 Mouser.com You'll have to filter the results and pay close attention, but I'm sure the connector you need is there somewhere. SMD Tool Map https://www.stevemeadedesigns.com/board/topic/193176-smd-tool-map-new-november-2014/ Build log https://www.stevemeadedesigns.com/board/topic/197217-reeds-03-tahoe-hat-sqaq-singer-xs-shca-cockbox-80prs/?page=32 Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.