Jump to content

Recommended Posts

$229 for 3000 watts sure sounds like the deal of the century! These Timpano amps have been showing up lately online and at the prices and rated RMS power, they sure seem like interesting amps. Today we take a closer look at the TPT-3000EQ 1 ohm model. Unfortunately, the amp didn't survive the Amp Dyno tests, but what happened? Was this a fluke? Incorrect test? Bad design? Let's take a closer look and find out...

 

Watch on YouTube in 4K UHD quality or embedded below:

 

 

 

See my videos on YouTube http://www.willistonaudio.com  Many tests and demos of OLD and NEW SCHOOL car audio gear!


See cool pics on Instagram @oldschoolstereo

Link to comment
Share on other sites

awwwww shit here we go! grabbing my popcorn now. LOL

 

thanks for the post Big D!


All SMD products + MORE available at my store here! https://wccaraudio.com/ 
wc2022-red-black-whitebg_1667625898__08138.original.png.02e514af82dce531edf1aa4a36851c60.png

Subscribe to My Youtube Channel! Over 1,000,000 subscribers strong! Turn on your notifications!
http://www.youtube.com/meade916

 

Follow My Instagram! Daily live feeds from the shop, exclusive content way before it hits my Youtube channel...and little squares with photo's in them :D
http://www.instagram.com/meade916

The Official SMD Facebook fan Page
https://www.facebook.com/SteveMeadeDesigns/

Follow my Tweet (Twitter)
http://www.Twitter.com/meade916
 

 

 

Link to comment
Share on other sites

There has been a ton of talk that this test was done wrong.  People saying it's a full range amp.  So it should have been tested at 100 or so and higher.  I'm not defending this amp as I'd never use it but why maybe that's something to look into

Link to comment
Share on other sites

47 minutes ago, ToNasty said:

There has been a ton of talk that this test was done wrong.  People saying it's a full range amp.  So it should have been tested at 100 or so and higher.  I'm not defending this amp as I'd never use it but why maybe that's something to look into

Full range as in it can play all frequencies 40 or the 1k shouldn’t of mattered

Link to comment
Share on other sites

2 hours ago, ToNasty said:

There has been a ton of talk that this test was done wrong.  People saying it's a full range amp.  So it should have been tested at 100 or so and higher.  I'm not defending this amp as I'd never use it but why maybe that's something to look into

Here are my thoughts on this. The amp is sold as a "3000 watt" amp and NO mention of mid/highs use. How many people buying these are using them for mids/highs? Probably less than 5% of buyers here in the US. If the amp is only designed for mid/high use, then you should EXPLAIN this to the consumer CLEARLY. Otherwise stuff like this is going to happen. Timpano made a follow up vid saying the Amp Dyno couldn't measure this amp properly, but they didn't get into the why. The amp puts out a lot of noise and distortion making it almost impossible to get a certified reading using this amp. They show an o'scope and say the signal is clean. You can't see THD on an o'scope and in many cases can't see clipping until it's too late. The worst thing to do here is to blame the person testing the amp. Take the data, make the amps better and let's try again. Oh yeah, maybe think about some overcurrent protection? 

See my videos on YouTube http://www.willistonaudio.com  Many tests and demos of OLD and NEW SCHOOL car audio gear!


See cool pics on Instagram @oldschoolstereo

Link to comment
Share on other sites

Good night friends.
I'm Daniel, I watched the brazilian hd3000 filter test video, and would like to see the amplifier test of this link, http://bandaaudioparts.com/en/amplifiers/ice-x/ice-x-3001/, this is an amplifier from the best brazilian amplifier manufacturer, this is the x 3001 band ice ... thanks in advance.

THANKFUL.
Link to comment
Share on other sites

2 hours ago, BigDWiz said:

Here are my thoughts on this. The amp is sold as a "3000 watt" amp and NO mention of mid/highs use. How many people buying these are using them for mids/highs? Probably less than 5% of buyers here in the US. If the amp is only designed for mid/high use, then you should EXPLAIN this to the consumer CLEARLY. Otherwise stuff like this is going to happen. Timpano made a follow up vid saying the Amp Dyno couldn't measure this amp properly, but they didn't get into the why. The amp puts out a lot of noise and distortion making it almost impossible to get a certified reading using this amp. They show an o'scope and say the signal is clean. You can't see THD on an o'scope and in many cases can't see clipping until it's too late. The worst thing to do here is to blame the person testing the amp. Take the data, make the amps better and let's try again. Oh yeah, maybe think about some overcurrent protection? 

I 100% agree.  

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Who's Online   0 Members, 0 Anonymous, 268 Guests (See full list)

    • There are no registered users currently online
×
×
  • Create New...