Neil Wheatley Posted November 7, 2014 Report Share Posted November 7, 2014 can torres be set to do a side port sub front so i can do a long straght port without having to bend it? Link to comment Share on other sites More sharing options...
Jessica Posted November 7, 2014 Report Share Posted November 7, 2014 can torres be set to do a side port sub front so i can do a long straght port without having to bend it? You will have to switch around the dimensions to make it work. But if you are running more than one baffle it wont Rest in peace, walled 87 accord build log 03' Corolla build with AA Mayhem inside. My super random youtube channel and terrible camera work. Wiring comparison by CaptainzPlanetz Wire and fuse guide by Guest SyKo13 Link to comment Share on other sites More sharing options...
Neil Wheatley Posted November 7, 2014 Report Share Posted November 7, 2014 only 1 baffle it just seems that its set to have the port on the front, im trying to build a box like on the kicker l5 tech sheet but tuned lower Link to comment Share on other sites More sharing options...
philrab Posted November 7, 2014 Report Share Posted November 7, 2014 Worst case scenario, just figure your net airspace and punch that straight in, bypass everything else. 2015 Toyota Tacoma Build Thread 2007 Mazda 3; 5000K HID's, Kenwood Excelon KDC-X997, Infinity Reference 6.5 comps in front and coaxials in the rear doors, JL 320.4 four channel, Rab Designs built ported enclosure with an SA12, Kenwood monoblock, Redline Leater shift boot/e-brake boot/center console cover, JBR short shifter/shifter bushings/rear motor mount. Build Thread 1996 Mazda Miata: Kenwood Excelon HU, Alpine speaker in the doors, Clearwater (miata specific) headrest speakers. 1994 Mazda Protege: Kenwood Excelon HU, Infinity Reference 2 ways all around, 2x RF Punch 10's in ported boxes. Link to comment Share on other sites More sharing options...
Torres Posted November 24, 2014 Author Report Share Posted November 24, 2014 a bit late on this, but in case you haven't figured it out you would just need to make the port dimensions match that of the side of your box. Link to comment Share on other sites More sharing options...
crownvicon28s Posted November 24, 2014 Report Share Posted November 24, 2014 Just downloaded the program but I think I have the old version. Trying to double check my box but there is no option to check for a slot port box. What am I doing wrong because my tuning is coming out all wrong? Edit: I figured it out. Link to comment Share on other sites More sharing options...
dharris2488 Posted November 26, 2014 Report Share Posted November 26, 2014 Here, I mirrored it in my Dropbox for whoever needs it. https://dl.dropboxusercontent.com/u/12084540/TorresBTC.rar Thank you... I've been pulling my hair out for the last 15 minutes trying to find this program. I like to use this for it's simplicity, as it is about as accurate you are going to get. Then I play around with WINisd to figure out what different Vb's and tuning does to the output. Good little one two combo... 2013 Toyota Camry SE 240a MechMan HO Alternator 1/0 Welding Flex Cable Big 3 CT Sounds 4000.1D Kenwood XR400-4 Mid/High Amp SoundQubed Q4-120 Mid Amp Infinity Kappa 6.5 components Kappa 6x9's for rear deck fill (coming out) (4) 8" PRV 8MB450's Set of SoundQubed SuperTweets (2) DSS Ethos 12's D2's @32.5hz (building 4th order enclosure) (2) SQ HDC3 10's @ 33.5hz (current build, loving them) Pioneer AVH-X4600BT 100 sq/ft Stinger RoadKill Sound Deadner 120 sq/ft QMat Sound Deadener (4) Juice Box Black Cherries Lots and Lots of feet of SHCA wire, along with 50' of Welding 1/0 2 Runs of 1/0 Positive front to back ToolMaker Everywhere Link to comment Share on other sites More sharing options...
dat Posted March 25, 2015 Report Share Posted March 25, 2015 wish it had a option for the cut sheet to include the angles need for a wedge box for my table saw. That would be ideal.! Thanks Torres Link to comment Share on other sites More sharing options...
Triticum Agricolam Posted March 25, 2015 Report Share Posted March 25, 2015 wish it had a option for the cut sheet to include the angles need for a wedge box for my table saw. That would be ideal.! Thanks Torres That is where SketchUp comes in! Different horses for different courses. "Nothing prevents people from knowing the truth more than the belief they already know it.""Making bass is easy, making music is the hard part."Builds: Link to comment Share on other sites More sharing options...
psc223 Posted May 11, 2016 Report Share Posted May 11, 2016 My version does not have the Slot Port check box or the Port Bend check box. Did you get rid of those boxes or do I have the incorrect version? Chris Torres v1.1 is what I've got.... Thanks Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.