Jump to content
Second Skin Audio

new box plans


scfaust

Recommended Posts

According to Torres calculator and the measurements given and 3/4 timber with single layer all round I get:

6.62cu ft after disp 72.5" of port tuned to about 34.3 hz.

Port area would be a little low for the size of the box still.

If the port was made to 6" wide and the section of port on the back wall increased to 7.75" long will keep a low tune and net much more port area 87" to be exact and the box volume comes down to 6.05cu ft.

What power will be runnning into the drivers at what load. The smaller volume and bigger port may or may not be a good thing.

Systems:

Fun Car:

Deck: Alpine CDA-9887

Front sounds: Alpine SPR-175A x2

Front power: RF T400.2 Benched at 265x2 rms @ 2ohm

Subs: RF T1 10 dual 4 Ohm x1

Sub power: RF R500.1

Box yet to be built.

All in a Mazda 323 Hatch in the cargo area only.

Daily hack:

Deck: Alpine CDA-9886

Front sounds: RF T152 5.25" coax x2

Front power: RF Power T400.2

Subs: Alpine SWR-1021d x4

Sub power: RF Power T20001

4.59cuft net 56" of port tuned to 32hz.

Work ute

Deck: Alpine iDA-X303

Speakers front: Stock

Speakers rear: None

Subs: Alpine type S SWS-1040

Amp: Alpine MRV-T320 x1 for woofer.

Box 1.42 cuft 39hz hidden under tray in blow thru design.

New ute to be much different.

Link to comment
Share on other sites

According to Torres calculator and the measurements given and 3/4 timber with single layer all round I get:

6.62cu ft after disp 72.5" of port tuned to about 34.3 hz.

Port area would be a little low for the size of the box still.

If the port was made to 6" wide and the section of port on the back wall increased to 7.75" long will keep a low tune and net much more port area 87" to be exact and the box volume comes down to 6.05cu ft.

What power will be runnning into the drivers at what load. The smaller volume and bigger port may or may not be a good thing.

what if i used 1 inch thick wood

Link to comment
Share on other sites

If the original plans were made with 3/4" stepping up to 1" will require re-working the design a little as the sheet sizes will be different. Are they to max dimensions that you can use or a design supplied with a woofer? even in 1" going with the external dimensions of the original plan will net a smaller box and different tuning.

Systems:

Fun Car:

Deck: Alpine CDA-9887

Front sounds: Alpine SPR-175A x2

Front power: RF T400.2 Benched at 265x2 rms @ 2ohm

Subs: RF T1 10 dual 4 Ohm x1

Sub power: RF R500.1

Box yet to be built.

All in a Mazda 323 Hatch in the cargo area only.

Daily hack:

Deck: Alpine CDA-9886

Front sounds: RF T152 5.25" coax x2

Front power: RF Power T400.2

Subs: Alpine SWR-1021d x4

Sub power: RF Power T20001

4.59cuft net 56" of port tuned to 32hz.

Work ute

Deck: Alpine iDA-X303

Speakers front: Stock

Speakers rear: None

Subs: Alpine type S SWS-1040

Amp: Alpine MRV-T320 x1 for woofer.

Box 1.42 cuft 39hz hidden under tray in blow thru design.

New ute to be much different.

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Who's Online   0 Members, 0 Anonymous, 271 Guests (See full list)

    • There are no registered users currently online
×
×
  • Create New...