MACnonsence6
-
Posts
2046 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Media Demo
Store
Collections
Videos
Posts posted by MACnonsence6
-
-
i bought this amp used on caco so it coulda been fucked to begin with. but it was running nice and strong for a few months. the time it failed was at or close to the time i had to put new lead wires on my sub so i think the lead wires might have touched.
my charging system is not the best stock alt in a 98 neon but its newer. 630 cca battery new as well with 4g bit 3 then 4g to the back of the amp running the amp at 2 ohm witch gain a lil over 1/4.
-
i had someone walk me threw and originally diagnose what was from on a diy forum. wich in turn that is what was wrong the last 2 fets on both sides in the line of power supply fets where shorted i took them out of the circut and the amp worked. thus showing what the problem was. everything else on the amp was fine i beleive the amp blew because of speaker wires touching. but then when i put in the new fets the ones this person told me to get wich were the ones i needed. when i go to hook everything back up the amp does its protect problem again.
i didnt just see something blown and be like ok ima replace this i looked into it got help then replaced them. maybe i did do something wrong will replacing them but idk. my bad about the title im just upset atm
-
so i put in the transistors my amp needed hooked it up all excited and shit turn it on and right back in protect mode shorted like 4 of the new transistors. now before i was using it with the shorted 2 out of circut and it worked fine actually thought it sounded alot better then before. then when i go to replace all of them. i get the same problem and all the money spent on new transistors is for nothing. anyone want a blown audiopipe amp get at me.
today sucks
anyone know of a good amp that will last a long time that does close to 2k at 1ohm. -
do your back seats fold down if so id face the box the other way firing into the cabbin and seal it off with some gorilla tape. cause judging souly by what i can see in the vid im doing way more flex with a single 12. you having 2 should be able to do some work id try sealing it off and see if u like it any better as oposed to how it is now.
-
1st gen neons 99 and older 1 12 sealed off in the trunk firing into the cabb and it makes it hard to breath.
running ap1800 @ 2 ohms and a re se 12. big 3 and stock battery upfront amp is deff not putting out anywhere what it should @ 2 ohms cause i dont have the electrical and it still makes it hard to breath with 1 12
-
i have mad old woofers but there all being used lol im a bit of a old school colector. ima take my time and get it right. this sub needs to be reconed anyway because of that but hopefully thatll prolong it long enough for me to get the money to recone it wich brings me to another question.
i have what i beleaive to be a pair of newer stlye re se motors on standered 12 spoke baskets. one reconed with a recone from fi but im not sure if that recone will work with the newer motors on 12spoke baskets as the new ones are on 4 or 6 spoke "dont remember" it has worked for the past 6 months or so ive had it but ive been wondering if i can stuff a 05 xxx recone in that motor. if so what benafits i get.
like what would be better in the same aplication 1 stock re se d4 wired to 2ohms on an ap1800 or 1 re with maxed out options from fi running d2s wired to 1ohm?
-
a friend gave me a pyle square 10 that the cone broke apart from the coil but there leads are flat and are just clued on the top kinda kool. couldnt do that with mine hopefully i can stich then and not fuck up sick of lead slap and worrying or worrying about them breaking off at the cone
-
alright when my leads get here ima do that sick of this shit lead slap and having to worry about the leads breaking at the cone
if i knew how to re string them from the cone id re wire them all so there was no breaks/ -
im going to be adding another 3" so theyll have plenty of slack.i only got one spider with this recone. re se from fi.
so id stich from to the high rib
-
they make curved needles why couldnt i do it with the recone already in? then put a drop of ca glue that would leak under and glue the bottom as well
-
get sewn in tinsel leads :-)
kinda 2 late now they have already be reconed where would i sew them on though the high ribs/ putting a needle threw the spider wont effect it?
-
i might need to do that all 4 of my leads have broke cause when i did my recone i didnt give them enough slack. and the leads i ordered to fix them where mad small im now odering .80 leads so i gotta eather do that ^ or extend the foam pad thats on there with new ones one each side
-
where would i find them at?
-
so i gotta find a foam pad thatll work and ca glue that to the cone
-
can you ca glue the lead wires to the top rib on the spider with added slack between the ribs?
-
was gona say ud be screwed if u ripped that lil sticker. not gona lie be kinda funny for someone to post something like this and not care cause its under waranty then realize they just broke the seal so now there beat lol
-
nope nothing like that in the bios but ik when i was running duel boot with 7 ultimate i had card settings that i could change so if i do run into a problem hopefully that should be able to fix it.
looking for a good express or usb soundcard for my laptop. need something amazing anyone used anything that they liked alot?
-
awsome thanks that was one of the other things i was worried about ima restart my laptop and see
-
thought amp manufactures wouldnt cover an amp that was opened?
-
turns out my power adapter wasnt bad so yay lol im running ubuntu atm so i cant check but lets say the 10" 30 pin screen worked but my laptop kept trying to put the 15" screens resolution to it so on the 10 i would only see the middle is there a way to turn resolution down to get it to fit the smaller screen if that made sence?
/ im in ny as well just way north
-
fyi i send 800 to my se all day and it loves it
-
i think i may have older se motors then would u do one with the boot of with a a bic lighter or something to show size? heres mine covered in bondo dust
-
should be pretty beast. those you can recone with re 05 XXX softparts just saying
/ pics? wana see the motor and see how much bigger it is compared to my sex motors
-
my plan to extend it is to buy another cable the one that goes from the board to the screen. that way i have 2 and i have 2 flat ends to solder to and no cable cutting.i really wana use my toshiba though because i already have it. and im kinda do this on the cheap and more of a learning expience over all. my only worry is that i wont be able to get the 10" monitor to work ima look more into it and see if a 30 pin is a 30pin no matter what hopefully if there not the same pin placement i can find diagrams and make it work. might have the money to buy that screen pretty soon sold some older home audio stuff. so a build log will be in progress. prolly start one tuesday as ill have the parts to fix my ap1800. thanks for all ur help throughout this im glad theres people like you here on smd wish there was more.
as far as using a computer and getting rid of the head unit that would be pretty bad ass plus with the sound cards u can get you have the ability to set up a pre out for highs mids and lows,/ isnt there a thing out there that boosts inline rca voltage? would that work for your aplication
anyone know of a good amp that will last a long time that does close to 2k at 1ohm..gif){kind=small}
f**k audiopipe
in General Audio - Can't find a category for your question? Ask here.
Posted
meaning what? lol i should be using hifonics equipment instead of re and ap