garrett30
-
Posts
106 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Media Demo
Store
Collections
Videos
Posts posted by garrett30
-
-
for that sub you can tune higher.. try a tuning closer to 35-36 htz youll be alot happier and it will free up some room in your box
thats what i was thinking them subs like it at around 36-38.... i am currently building a box for these same subs but i got it tuned to around 35-36. right now i have them in a box thats tune to 39-40 its ok but im building a new one to tune lower. good subs by the way
what would i need to change on the box design above for it to be tuned around 35hz?
-
Ok so the AQ SDC2.5 work best on 4-4.5 cuft per sub and 14-15 sqin/cuft so you are low, here is a design suggestion on your space:
Enclosure Specifications:
Fb = 32,351 Hz
Vb = 7,67 ft^3
Subwoofer Mounting = Flush Mounted
External Height = 17 in
External Width = 38 in
External Depth = 30 in
Port Width = 6 in
Cut List:
* All Dimensions in Inches.
* Wood Thickness is 3/4 for all Parts.
External Enclosure Parts:
Front = 31 1/4 x 15 1/2
Front Internal = 30 1/2 x 15 1/2
Back = 38 x 15 1/2
Left & Right Sides:
Side 1 = 28 1/2 x 15 1/2
Side 2 = 27 3/4 x 15 1/2
Top & Bottom = 38 x 30
L Port Internal Assembly Parts:
Front to Back = 19 1/2 x 15 1/2
For your type of vehicle is recommended subs/ports in the same face front or rear firing so both should be tried.
Here is an assembly guide (generic dimensions):
thanks i will get some wood and get it pput together!
-
I have 2 AQsdc2.5 15's and the dimensions are 38"Wx30"Dx17"H. I would like the tuning at 32hz and i have a 1999 ford contour.
-
I am wanting to do a rebuild with my new AQ sdc2.5 15's and need a little help with designing a box. Anybody on the forum intersted in helping a fellow basshead out?
-
I asked 412 cvx to design a box for me and I am not allowed by my parents to create a paypal account, how do you setup an invoice for me to pay with my debit card? I know it can be done because i payed for a custom xbox controller this way(no it was not from ebay or any site similar). Any help is greatly appreciated.
-
Question about the vent holes that let pressure out, if seal, would it make something dangerous or anything?
No there are enough spaces and voids on the trunk, deck, and back seat that allow the pressure into the cab of the car. it will just put more air movement through the car and not straight out of the side of the trunk.
-
put foam inside the weather seal area. thats whats rattling most likely
as well as the area where the latch is.
some cars are able to have the ring that the latch attaches too move down for a tighter fit.
id be verrry careful if you put spray foam where the weather seal is if you put too much it could warp it then it will be raining in your trunk.
Could I use dynamat on the trunk lid where the weather seal sits?
-
put foam inside the weather seal area. thats whats rattling most likely
as well as the area where the latch is.
some cars are able to have the ring that the latch attaches too move down for a tighter fit.
Alright I will try this tomorrow. thanks
-
hey there guys I have a trunk car system and i have put sound deadener on my trunk lid, on my license plate and i have also put expansion foam inside the trunk lid, but yet i still rattle like a mother and it is coming from he trunk. Any ideas on what to do to remove or dampen the rattle? thanks in advance for the help.
-
I have been running street wires zn9 series for awhile now and never had a problem.
-
-
I get 9^3 gross, so you're probably way on the small side with port/subs subtracted.
What are specs for the port opening? I see 15.5 high, but how wide is it?
How does it sound so far as this box "seems" to be way out of whack for those subs...
the opening of the port is 4.25". And hits pretty good on some songs and sounds bad on most. i had a buddy design it and i juta put it together
Sorry to say but that box design is junk for those subs. 8cubes NET is the smallest I'd do, 8.5-9 is better with 16^2 port per cube. You're around 10^2 per cube if you're lucky and it's tuned way too low.
If you give me your max dimensions I'll see if I can come up with a better design that will fit.
How much power do you have?
max dimmensions are 38Wx17Hx40D and at 2ohms i can run 500rms to each and at 1ohm i can run 750rms to each.
-
I get 9^3 gross, so you're probably way on the small side with port/subs subtracted.
What are specs for the port opening? I see 15.5 high, but how wide is it?
How does it sound so far as this box "seems" to be way out of whack for those subs...
the opening of the port is 4.25". And hits pretty good on some songs and sounds bad on most. i had a buddy design it and i juta put it together
-
what are the port specs of the box
[/quoteits an L port and the specs are 25"Dx15.5"H and 14"Lx15.5"H
-
Really curious on box specs as I don't see 2 of those fitting in a trunk in the proper size enclosure.
Especially tuned to 27Hz as that's a long ass port if you did 16^2 port area per cube.
As for trunk set ups my experience has been rear facing hits lower, forward firing peaks a little higher and is louder. Also sounds a little better on real music. Of course every car is different...
the specs are 38"Wx17"Hx29"D and by my measurements and using a online calculator it shows that my slot port is at 27hz.
-
I just installed 2 aq sdc2.5 15's and I am wondering if it would be better to leave the back seat down or o put it back up? the box is tuned around 27hz and is firing forward.
-
Hey SMD forum people I have recently gotten two AQ 15's and i have a custom box that is tuned at 28 hertz. I am looking for some good songs with some low hertz. I might post up some vids of some of the suggestions.
-
I agree to the rules and terms above
1999 Ford Contour
Good luck and merry Xmas bassman
-
port layout
port is fully constructed
Subs installed
deciced on doing bolt terminals
got them in the trunk!
I Had 3/4 of sheet left. what to do with it? I know build an map rack! her are the pics
Hifonics HFI1500d(subs)
Kicker 550.2 on the fronts. (temporary)
Amp rack installed!
Stay tuned in next week i get my 2nd battery and 0 gauge wire! also hopefuly some vids of flex and excursion!
Hope you enjoyed it.
-
-
the message board code still didnt work
-
-
Use the img code, and its not ubl?
oh lol I didn't realize i put ubl in the title. I was talking to a buddy about ubl's and it must have slipped in there.
-
why wont this let me post my pics?
box design help
in Subwoofers / Enclosures
Posted
what wattage do u have urs at, cause mine are on 500wrms and they make a popping sound when i go 3/4 to full tilt.