[help using my smd dd1]

i tested each SET of rcas to find there max. my rca for mids and highs was 36 volume and sub rcas was 38. so therfore max volume is 36 do for each set of rcas and each amp

and this is to set the deck only correct ?

Yes

so after i set my deck do i just plug the rca's back into the amps and use the + and - wire set to set my gain's on both my amps at the volume my deck go up to with all settings on my deck turn to flat and even on my amps

No. DD-1 clip to ground, put the probe on the + on the amp.

Did you even open the manual? It tells you how to do ALL of this

yeah i did read it i was just confuse about the head unit part where it told me to turn everything to flat

[help using my smd dd1]

i tested each SET of rcas to find there max. my rca for mids and highs was 36 volume and sub rcas was 38. so therfore max volume is 36 do for each set of rcas and each amp

and this is to set the deck only correct ?

Yes

so after i set my deck do i just plug the rca's back into the amps and use the + and - wire set to set my gain's on both my amps at the volume my deck go up to with all settings on my deck turn to flat and even on my amps

[help using my smd dd1]

i tested each SET of rcas to find there max. my rca for mids and highs was 36 volume and sub rcas was 38. so therfore max volume is 36 do for each set of rcas and each amp

and this is to set the deck only correct ?

[help using my smd dd1]

Some have a really weak output on the RCAs and the dd-1 doesn't get enough input voltage to work properly

i have a eclipse cd5030

[help using my smd dd1]

doesnt matter. i used red.

now what about my 2 amps do i just leave the rca's hook up to the amps and use the speaker + and - after i set my deck

[help using my smd dd1]

Did you read the manual?

It tells you to turn the crossover all the way up

yes i did it said turn it all to flat which i figure was turn off

[help using my smd dd1]

plug rca into dd-1 find max volume. then use probs on the amp to find max gain on amp ?

do i plug the red or black rca into the smd dd1

[help using my smd dd1]

why cant you use it just through the rcas? i had that same problem, wasn't detecting signal so once i got to 1/2 volume it worked. easier then testing through the amp

how would i do this for all my stuff like my amp's and deck

[help using my smd dd1]

what about my deck i can turn my sub control bass and terb to 0 but on my cross over where i set my slope and my cross hz it won't go down to 0 even for my front and back speakers to. only thing i can do is bypass it by turning it up to 200hz and set my amp instead.

[help using my smd dd1]

For the headunit just make sure the treb bass and if you have it sub vol to even

sorry let me make sure i got this right for my headunit i wanna set my bass and terb and my sub control on my deck to even.

[help using my smd dd1]

hi everyone i have a question i just got my smd dd-1 in the mail yesterday and i was gonna tune my system and i was reading threw the manual on what i need to do. and i have a question i am doing the measuring a head-unit through an amplifier and i see it tells me to set my eq and crossovers on the head unit and amp to flat but my problem is there no way i can set the eq and cross over on my deck to flat and i am not sure what to do.

head unit - eclipse cd5030

sub amp - plye drive plad 3300d

4 channel amp - rockford fosgate dsm4040

sub's - 2 12 inch sundown audio sa's dvc 2 ohm.