Jump to content

j_black10

Members
 View Profile  See their activity

  • Posts

    1206

  • Joined

  • Last visited

 Content Type 

Posts posted by j_black10

  1. Got A Ticket Today

    in Off Topic - Random, Misc posts - the forum "Junk Drawer"

    Posted

    200 bones in my Hicktown, Natchez, Mississippi...These idiots drive around pulling imports over for exhausts...When god damn Harleys with shorties and 18 wheelers with no mufflers rattle by me while I am pulled over...F ing pigs...I hate em...

    X2!!! It's $275 in Tupelo, MS! I don't think they give tickets in Jackson though! I've seen ppl right beside the po-po, beatin' the block down and they don't do a thing to them.

  15. Two Questions...

    in General Audio - Can't find a category for your question? Ask here.

    Posted

    Any thoughts on my other question? :mellow:

    You still will be able to master/slave those amps together. It seems though that one amp may be more powerful than the other.

    I know some of the earlier model T10001bd only put out alittle over 1000w @ 1ohm and the newer models are around 1500w @ 1ohm. My board is red and mine is a refurb of the 2006 model. It didn't come with a birthsheet but I know it's putting out around 1500w rms.

  18. One Amp In, One More To Go!

    in Amplifiers

    Posted · Edited by j_black10

    Just for reference, every T10001bd birthsheet I've seen has been in the 1500watt range.

    Just going by ear, this one has to be putting out around 1500w rms cause for the little time it plays before going into protect, it pushes my subs harder than my brutus did, which was rated at 1500w rms.

  23. One Amp In, One More To Go!

    in Amplifiers

    Posted

    Yeah I thought it was weird too. I use to have a RF 1001bd (2 ohm stable) and ran it 1 ohm all day long with no problem. And this one plays fine at .7ohms at a lower volume, but when I crank it up it will play for about a minute then I goes into protect mode. Though it might be because of lack of voltage, but it stays around 14 volts. I also checked the remote wire voltage and it stays constant at 12.8 volts. I think it depends on the amp and I just got one that can't play below 1 ohm. No big deal, I had already decide to get 2 of those bad boys anyway, for future plans!!!!

    Also, this one amp pushes these Qs way better than my old Hifonics Brutus bx1500d did!!! Although that brutus did run at .7 ohms all day long.

  24. One Amp In, One More To Go!

    in Amplifiers

    Posted

    Oh yeah, I found out I can't run this amp at .7 ohms. It goes into protect mode when I really pump my music with both subs hooked up. With just one hooked up at 1.4 ohms, it will play all day long at full throttle!! So I series both subs together at 2.8 ohms and it plays fine!! Subs are underpowered though but I gotta have some bump!! LOL!! I'll run it like this for now, until I get the other amp!!!

  25. One Amp In, One More To Go!

    in Amplifiers

    Posted · Edited by j_black10

    Well I finally decided which amps I was going to get, so I chose these bad boys

    Image005-1.jpg

    Image004.jpg

    Image008.jpg

    I was only able to get one T10001bd right now, anniversary comin up so you know were my money's going!!! LOL!!

    I'll get the other T10001bd at the end of next month, Can't wait!!!

×
×
  • Create New...