Electrodynamic Posted August 8, 2011 Author Report Share Posted August 8, 2011 It was sealed up on the dash in the legal position. We are going to install the loading wall tomorrow and take more TL scores. Quote Electrodynamic Power handling is not a power requirement! Don't install suckage! Simon Eichenberger is the man. My PM's are disabled. Link to comment Share on other sites More sharing options...
Electrodynamic Posted August 10, 2011 Author Report Share Posted August 10, 2011 Quick video we took of Paco's build immediately after we finished temporarily installing the loading wall. The wall needs to be fiberglassed over, holes sealed up, expanding foamed, etc. Then the entire outside shell of the box needs to come off, wood glue applied, and then re-mount the boards with double the amount of screws. The amps aren't gain matched at all, etc. But even in its crippled state it's pretty stinking loud! Quote Electrodynamic Power handling is not a power requirement! Don't install suckage! Simon Eichenberger is the man. My PM's are disabled. Link to comment Share on other sites More sharing options...
Electrodynamic Posted August 11, 2011 Author Report Share Posted August 11, 2011 New video taken earlier today. Quote Electrodynamic Power handling is not a power requirement! Don't install suckage! Simon Eichenberger is the man. My PM's are disabled. Link to comment Share on other sites More sharing options...
2loudisjustright Posted August 11, 2011 Report Share Posted August 11, 2011 ^^^Sick nasty!! Quote 2000 zx2: Rebuild with 8 12s on a 10k underway!! MY BUILD LOG Link to comment Share on other sites More sharing options...
Electrodynamic Posted August 11, 2011 Author Report Share Posted August 11, 2011 We took out the loading wall / port and got it prepped for fiberglass mat and resin today. We wrapped the bolts with latex so the resin would not get inside the "tubes" and make it hard to get the bolts back in: Then we laid down fiberglass mat and resin on the back side of the port wall to seal it up completely: Right now we are waiting on it to dry. Tomorrow we will sand down the high spots on the back of the port face where the glass and resin is and re-install it along with using expanding foam to seal up any gaps. Quote Electrodynamic Power handling is not a power requirement! Don't install suckage! Simon Eichenberger is the man. My PM's are disabled. Link to comment Share on other sites More sharing options...
Electrodynamic Posted August 12, 2011 Author Report Share Posted August 12, 2011 We put Sundown Audio's FedEx rep inside the truck for a demo / hair trick without the loading wall being installed yet: Quote Electrodynamic Power handling is not a power requirement! Don't install suckage! Simon Eichenberger is the man. My PM's are disabled. Link to comment Share on other sites More sharing options...
ty_houston Posted August 13, 2011 Report Share Posted August 13, 2011 are the obsedians like the sundown sa? what's the rms rating on this? build is nice...Loud! 157 with no loading wall or tuning...good shit Quote supercharged hummer h2 8 Sundown nightshade v'2 Scott Bowman built 4th order bandpass 2 precision power pcx 4125(mids & hi's) 2 Stetsom 14k2e's alpine ina-w910 dual Mike Singer350 amp alt 8 kinetic 2400 batteries two shuriken bt 120 1 kinetic 2000 under the hood link to build log: My link Link to comment Share on other sites More sharing options...
Electrodynamic Posted October 6, 2011 Author Report Share Posted October 6, 2011 New video taken today: Quote Electrodynamic Power handling is not a power requirement! Don't install suckage! Simon Eichenberger is the man. My PM's are disabled. Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.