Boomzilla

Anyone?

Which do i need of these, and what is their purpose?(sorry for the noob question) SOUNDSTREAM XBP-10 : SPL Competition Signal Processor • 2 Signal Paths – Sound Quality & Sound Pressure Level • Individual Level Control for each Signal Path • 5Volt or 10Volt Signal Voltage Switch • 50Hz Tone Generator for Tuning • Variable 25-85Hz Bass EQ • Backed by one year manufacturer waranty • Dash Remote with Boost Level, Subsonic Filter, and SQ-to-SPL Signal Path Switch • 4 Pairs of Outputs – 1 Main and 3 w/ Variable Delay for Time Alignment of Subwoofers • Through Pass Outputs • Turn On/Off Delay to Eliminate Pops SOUNDSTREAM INT-2BX : Digital Equalizer with SUB woofer output • 5 Channel Hi-Level Input • 4v-30v Input Sensitivity • Variable 30-80Hz Bass EQ • Variable 0-12dB Bass Boost • Variable Boost Q • Subwoofer Input Selector • Backed by one year manufacturer waranty • 15-50Hz Subsonic Filter • Remote subwoofer gain control • Front, rear and Sub Low Level Outputs • Delayed Remote Turn-on Output • On-Board Clip Indicator • Signal Sense Auto Turn-On SOUNDSTREAM BX-20Z : Digital Bass Reconstruction processor • Max. Bass Control • Dash Mount Remote Control • PFM Subsonic Filter & bass level Control • illuminated logo and knobs • brushed Aluminum Case • Chrome Logo Plate • Bass Restoration Lighted Display • Backed by one year manufacturer waranty • Parametric Bass Control • PFM Subsonic Filter • Balanced Inputs • Bass Output Control • PWM High Head Room Power Supply • Output Level: 13.5 volt • Frequency Response: 10Hz 100KHz • thD: 0.002% • S/N Ratio: 132db • Balanced Input Noise Rejection: 60 dB Not sure if I need 1 or all 3, trying to keep 1 brand for as much as possible, I have all tower amps, 2xdtr1.3400D and 3xdtr4.680, soundstream hi's mids midbass, I've always just ran a basic 3way electronic crossover, but I want to do it right this time. Any advice or info is greatly appreciated.

8ft exactly truck style size box

How many 4" ports would be needed for a BL18 and how long should they be? Tune to 33hz is the goal

Well the ssd15's hold 800rms each and BL18 holds 1k rms, so would 1400 on 1 18BL be better than 700rms on each SSD15? we only have 8ft to work with, and want the best flex possible.

Hello my brother has a ford ranger with a box that has exactly 8ft of air space and a MMATS 1400RMS amp, would 2 SSD15's or 1 BL18 flex harder? 2nd question: Will 4" PVC pipe work for the ports? if so how long and how many should we use? Thank you.

Nuff said.

Grats on the subs! Let me know how it sounds when you get it rumbling.

Well I am going to run a goliath on 2 18" BTL's and wasn't sure if I needed them fully loaded or not.

I miss worded my question, I ment what does a fully loaded BTL have over a non-loaded BTL?

What advantages does a fully loaded btl have over a reg. btl? Is fully loaded for SPL only? Why does one need to be fully loaded? EDITED**

Goliath it is! I can get them for around 950-1k$ each and might run 4 btl18's and 2 goliath's, then again might try 2 btl18's first and add 2 more later.

Nice! I am looking at a HiFonics Cyclops or Goliath per 2 18's, thats 2k or 2500 each depending on which I choose, which do yall recomend?

I have decided if I am going FI that I need to go BtL over BL, and need some help on the RMS figures. I know Steve runs 4kRMS per 18 and does very well, but how do these subs respond to only 2krms each? I have heard they can eat up 10krms each and keep going. Do you need the full options to run higher power? Will the differance of 2krms to each versus 3krms or 4krms to each be that massive? This is a Daily driver vehicle. I am planning on running Hifonics amps. Thanks for any advice.

I don't know if anyone has mentioned this(kinda new here), but Toccata by Manheim Steamroller on the CD Fresh Aire III has an awesome sweep of all tones, and the bass is a growing rolling tone, and the highs will work even the best high setup. I tryed to upload it, but it wasnt happening >.<

2001 chevy blazer

I live in Dallas,TX

Yah that big I'm going to need to have 1 built, so yah.... WTB: a box for these subs lol.

WTB: Custom box for 4 18" Fi:BL's I want it vented, thinking vent facing the back and 4 subs firing straight up. Not sure if this will out-perform a wall, but i want to flex, and this is a daily driver. subs are 1000watts RMS I will be putting 1200 watts on each. Not sure of the frequency I need, but 45hz sounds too high, possibly round 30-35hz. I want to hit decent numbers, and flex the hell out of my SUV.