BulletInjection
-
Posts
2685 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Media Demo
Store
Collections
Videos
Posts posted by BulletInjection
-
-
?? no, even with the use of a slot port, i get a length of about 35" for the tuning to be at around 32 hz.
-
?? no, even with the use of a slot port, i get a length of about 35" for the tuning to be at around 32 hz.
I even used your calculator and that's what I got. Then I used one from Alpine and theirs said like 19.5. So my results from the two were 18" and 19.5"
-
vent length seems to need to be 22-23 in, 22 is probably safe anyway hope this helps
Whhaaatttt, really? that seems very long? But what about if you are using an outside wall as a port wall, how far in and over would I have to make that port if the OD of the box is 16in tall
-
I have a design for a box but I need the tune to be 32 hz.
(OD) 16 tall, 39 wide, 27 deep
(ID) port 22.5 tall, 4 wide, 18 length
sub disp. .26 (Fi BTL 18") :hairtrick:
idk about port length because there are outside wall compensations and stuff that I dont get so please help. slot and sub will be facing up
-
isnt a 4 inch port like only like 12.56 sq inches
so youd would need like 2 or 3 of these ports.
or you can probably get away with 1 6 inch
22.5 in tall so its 90 inches of port area which per ^3 foot for my sub is 12in-16in so its about right? I think? wth idk I am in no condition to be making these decisions right now
-
well most people that i see with them run 3-4 thousand to them i mean look at meade for an example 4000 a sub the 2610 will probably give you between 2400-2800 depending on voltage but no more than that.
@ 13.8 but im getting an mla module... maybe if I don't have to rewire my whole shits... pro kit only fits my car... but no matter my power I still need to know about my port GUYS. port is 22.5 tall 4 wide and 18 in length, and this is on 8 cubes (16x39x27)
-
the btl are going 2 want more power
they are rated 2k rms and im giving 2.6k rms, how hungry can they be!? lol
-
what power are you using?
bxi2610--- 2,600rms @1ohm
-
Use ExpoSport/'scalc.. its super simple and accurate as they get. its in the general audio forum
Yeah I used it and I got
16 x 39 x 27
slot: 22.5 x 4 x 18 .26 sub displacement
and that got me 8 gross cubic feet with 6.39 net @ 31.99 hertz
tell me waht you think
-
check out what i did for mine..
it was the one about advice.. i think i got it right now... go to this site... even give u the pieces to cut. along with the hertz... worked really good for me.
Yeah It does help a lot but just my lack of knowledge when it comes to overall port length and stuff. The over all port length is just how deep and inward it goes?
-
I want to get 7-8 cubic feet in the back of my 01 jeep grand cherokee which is 39 wide, 16 high and 27 deep (ID). I was wondering if someone could help me to plan and tune my box to 32Hz. Thank you
.gif){kind=small}
Is This 32 Hertz?
in Subwoofers / Enclosures
Posted
I just ran out and looked at the back and thought and measured and figured this is better. The port runs down 11in. port and sub face up.