[my jeep]

anybody got any comments that'd be cool

[my jeep]

[My first build]

Done now untill rhino lining.

And video of them in action this is without my new battery still it comes on the 13th. The other vids on my profile are with the old box and shit 4 gauge.

[My first build]

Sanded down

Right before amp

Gettin ready to put in the jeep box is done for now..

It's in there now i'll try and have pics tommrow

[My first build]

Thanks guys

[My first build]

Got wiring in today

Took out seats and pulled back carpet

And soldered the wire into the ring terminals

Box lid is on with some more liquid nail and screws letting it dry over night then sprayin the outside in rhino lining.

[My first build]

Taking out old wiring... melted fuse block..

Shitty 4 gauge.. theres my problem.

Ground

Amp with new reducers for the 0 gauge

Back emptied out

Sub 2 of them

Box build up

[Fuse Holder Meltdown?]

yea exactly what i was thinking more convenient and no blowing just didn't know if they were gimmicky or not

[Fuse Holder Meltdown?]

well im positive my ground is good i already had had a problem with it so i grinded down the paint on the frame and bolted it down and sprayed no rust on it and for the fuse i was thinking of getting a 140 circuit breaker do those work or should i stick with an anl with a 150 amp fuse or a afs fuse those seem pretty cool.

[Fuse Holder Meltdown?]

so even if i upgrade the fuse chances are all burn it up again?

[Fuse Holder Meltdown?]

I have 2 fi ssd 12's hooked up to a hifonics 1610D mono amp at 1 ohm i have it ran with 4 gauge wire and the fuse in the line after the battery i've had two holders melt down now.. What the hell is going on? the original fuse was a 125 and then i went to a 100 now im at nothing till i get another holder.

[Ohm Load]

ok thanks guys

[Ohm Load]

the speakers are 1 ohm though

[Ohm Load]

See i had it set like that but there in 2 separate sealed boxes so i tried to cheat and rather then connect the 2 subs positives and negatives together i ran both subs to separate outputs. There 12" Fi SSd's 1 ohm and my receiver has 3 volts for the pre amp

[Ohm Load]

A hifonics 1610D stable at 1 ohm i upgraded the big 3 and have a yellow top and my ground i peeled back all the carpet and grinded off the paint and its straight to the chasis

[Subs Arent Comeing On.]

Yea it's the amp for sure i've had the same problem with 3 different hifonics amps now and i have it wired the same way

[Ohm Load]

Anyone?

[Ohm Load]

I wired it to a 1 ohm load but instead of connecting the wires before they get to the amp i have them both going to the separate outputs and all the gains and adjusts have only been about 1/8 the way

[Ohm Load]

well i don't know because i've had 3 amps fuck up now

[Ohm Load]

If i wire 2 dual 1 ohm subs both with 1 set of coils connected and then run the other wires to a mono amp and i put them both in there own slots since it has 4 outputs am giving the amp a .5 ohm load because the amp wiring the connections in parellel internally?

[2 12" Fi Ssd's 1 Hifonics 1610d]

Not great yet just getting started

[Crunch Amplifiers? Any Others Recomnded?]

for 299 you can get a dat hellfire 1000.1 great amp

[Need An Amp]

well found out they both cost exactly the same lol even down to the shipping. So i think im going to go with the hellfire because there are actual test ratings and there pretty high over the vfl 100 and i cant find the 110 anywhere and that one would be more expensive

[Need An Amp]

well is the vfl 100.1 good? and are they better than the hellfire amps because those look pretty nice

[Need An Amp]

well if there all very close whats the cheapest because i can't find a price on the dat or american bass amp. i found a vfl 100.1 and it says 1500 watts. is it actually 1500?