-
Posts
5124 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Media Demo
Store
Collections
Videos
Posts posted by fox_racin4
-
-
new deck, same problem
i think they all do it, kinda of hard to watch all 12 of them at the same time since i dont want to leave it playing when said problem happens.. uploading a new/better vid
-
did you unhook the other six and see if the ones you unplugged first look the same?
yes, same problem swiched RCAs from master amp to other master amp, same thing
only happens in the mid 40hz area, will try a new deck and then rewire for the 4th time lol
-
if you want to keep the same box, and if its a box problem, put 10" sono tubes behind every sub that are at least as long as the sub is deep. im not sure what length would be best though. that will help even out the pressure behind each sub.
^this. Cross directional loading was my first guess.
still does it with 6 not hooked up, which eliminates it as a loading issue
-
tried swapping RCAs same issue, my next step is a new deck..
-
keep an eye on the ipod cabke.. my dash has eaten 2 so far.. lol
-
i shall give that a try! i do need to rebuild baffle soon.. but it will still be either port accross top or some type of clamshell.. no side ports for me..
-
I do have a TL here, The thing that gets me,is the SA10s were fine, and they were getting quite a bit more power
Where should i place the TL? I dont want to keep playing it when the "problem" is happening, as im sure its not very good for the subs lol
-
doublecheck all subs and wiring
wiring has been more then tripple checked lol
-
if you want to keep the same box, and if its a box problem, put 10" sono tubes behind every sub that are at least as long as the sub is deep. im not sure what length would be best though. that will help even out the pressure behind each sub.
thats what next.. apparently it helps alot and usually gains quite a bit, even tho its not built for numbers
-
I know you probably have check the subs to see if you got the correct coils, I had 2 of my 16 subs show up and it had dual 4's the rest were dual 2's.
both sides read 1.2ohm on DMM
sounds like scratching....maybe
shitty camarah ftl theres no scratching
-
heres a shit wiring diagram
basically, theres 6 subs per pair of 4500s, at 1.2 strapped
theres 4 sets of .66 loads, which i seriesd to 2 1.2 ohm loads
so each pair of amps has 6 subs at 1.2 strapped
-
-
15cubes before sub displacement And 4 sax4500s at .6ea Subs are probly getting just over rated power
-
I need to doors closed to demo, 1. It 6758 times louder and 2. Subs unload quick with doors open Thing is it never did it before, and the HZ area it does it in is where i bassrace...lol
-
I need to doors closed to demo, 1. It 6758 times louder and 2. Subs unload quick with doors open Thing is it never did it before, and the HZ area it does it in is where i bassrace...lol
-
ill try to get a vid of it.. it seems to be 3 or 6 of the subs behind the drives seat, kind of hard to watch all of them hahaha
anything in the mid 40hz area will do it..
gotta run out for a bit will try to gets a vid!
-
never did it with the SA10s tho!
-
Ok, have an odd problem i need some quidance with... Playing the subs ( AB XFLs ) and songs that have notes in the 46hz area ( lil jon push that, The higher note in no hands) The subs behind drivers seat will unload. They do it with and without the seat in the truck. Any other notes are fine as far as i know... Tried re-wiring the subs, switched amps (switched leads at amps) Im out of ideas
-
Heard some hella nasty belt slip goin on near the end... but nice vid mang.
haha yep.. i need a shorter belt but cant find one.. it only slips when i load the alts down tho
-
No.... Its a very common problem
-
If i had more free time Id say get te wood , and a table saw And lay my gas thre and back and id help ya
-
im not to far i dont think, im a few min from detroit, in Windsor eh
-
If you know what your doing...yepp
-
Dont make me drive to OH!!!
I seen JB weld, But then he said weld With no JB infront of it.. And me being a welder When i see weld i dont think of jb weld lol
new subs.. new problem
in Subwoofers / Enclosures
Posted