-
Posts
5143 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Events
Media Demo
Store
Collections
Videos
Posts posted by RickyFriery97
-
-
Looking good so far! I have a 97 Burban
-
It's for ease of wiring. On my RF T2500BDCP I have a 2ohm load going into each input. The amp is internally bridged so that makes my final load 1 ohm
-
You are good it wont make a real noticeable difference, the new basket was jsut made that way for additional cooling.
thanks for the reply man, i went ahead and got em in and there sounding great
-
My used on is from cj alsoIve got 2 with the holes and 2 without in my tahoe. I done the same thing and bought 2 new and 2 used from cj. I havent noticed any difference really as far one getting warmer than other. Im running one dc 5k at .5ohm to all 4.
I'll run them and see if I notice anything
Thanks for the reply!
-
One of my XL 18s I bought new from DC
One I bought used and reconed.
The newer basket has openings where you can see the coil for cooling I'm guessing, the other does not. They are both M1 model XL
Pics:
Newer sub
Used one
-
No, only to sellThere is a want to buy section
there is also a minimum post count to post a wtb isn't there?
-
Ive been trying to down load the test tracks but after the download finishes I can't get them to open in iTunes.
I still have my DD-1 disk, can I just import them off the disk? Is there a certain way I have to import them?
-
Price for both shipped to 77573
-
hell yea nice choice! been waiting since i saw your FB post.
im assuming they will be on RF power?
Also cant wait to see the new SMDs
-
seen that too, just been ignoring it though.
-
Thanks alot man! sorry about the mix up, glad it got there though! enjoy
-
id do one positive run, and one negative run from a engine ground. also you could do a extra 1/0 frame ground.
-
Glad you're your for it! good luck man
-
I like this idea! Subscribing now!
-
you cant even read the numbers. what vehicle is this going in?
-
-
my burban use to do sealed up hairtricks in the back seat, no vids though
it was 4 L7 15"s on 4 POS crunch 2ks
-
Use a O-scope or a DD-1
-
straight to my D3100 in the rear, the D3100 is grounded straight to the D3400 under the hood then grounded to engine block grounds
-
put em in a vice and use a step down bit. takes no time at all
-
I was offered a job at Frys as a installer, as long as i was certifed they said i would start at $11.75 an hour. This is more of a hobby for me though. I think it would kill it for me if i took it on as a daily job.
Try to get some more hands on experience , also stick around here. You can learn alot just from this forum.
-
If it were me, id run atleast one 300+amp alt, or duals if its possible on the vehicle. Biggest XS power Batt you can fit under the hood, Big three in 1/0. Atleast 4 Runs of 1/0 (2+/2-) and at least two XS D3100s or the XP3000s. Notice i said atleast, no such thing as overkill on electrical.
I see I alreadly have a mechman 330, four kinetik hc2400s, four runs of 0 guage , optima up front ,,, problem is I'm dropping below 13 at full tilt while sitting at idle.
Theres your problem, most bigger alts like your mechman 330 amp dont put out much at idle, whats your voltage like when holding about 2k RPM?
-
If it were me, id run atleast one 300+amp alt, or duals if its possible on the vehicle. Biggest XS power Batt you can fit under the hood, Big three in 1/0. Atleast 4 Runs of 1/0 (2+/2-) and at least two XS D3100s or the XP3000s. Notice i said atleast, no such thing as overkill on electrical.
-
my iphone charger isint long enough so i have to use a extension cord..
Quick Pac-lc1 question
in Amplifiers
Posted
Just plug it in and go, no need to re set the gains