Jump to content

mattB9097

Members
  • Posts

    19
  • Joined

  • Last visited

Everything posted by mattB9097

  1. ok well i keep getting a bad tuning frequency but i'm going to have to live with it. the subs need .9-1.5 cubic feet each My trunk is 14H X 40W X 18D Can someone try to create a box with a tuning that is like 38-41hz (if thats possible) Thx
  2. Ok thats what I figured. what would be a good tuning frequency for my subs? People are saying like 35 (which i want but i cant get a box to do it) and some say like 40-44hz is good too...
  3. i was thinking...would it be better to do 2 ports..one for each sub, or one big port?
  4. ok. The BXI1610D is rated for 1600 rms x 1ohm. take away some of your watts loss due to wiring (because we all know its hard without spending a lot of money to get all 1600 to use), your subs will be roughly receiving 150 watts over (per sub) or 75 watts over (per coil) IF you wired it at a .5 ohm, you will probably (just a guess) but up to 1600 or a little over in watts going out. My buddy did this with his type r's. his type r's are receiving about 200-250 watts over what they are rated for, and there is no problem with them. now you could wire it to 2 ohms and push 1100 watts through, but then you are looking at a shortage of 50 watts per coil loss. If I had to pick, use the BXI1610D and wire it to .5 ohms and see how it goes...have your gain and stuff turned down at first and dont bump the s**t out of them right away. 1600watts (or about 1500) is enough for your subs.... hope this helps some..
  5. hifonics amps are really good for the money. My buddy has the BXI1610D amp for his 2 10" type r's 2x2ohm wired at .5 ohms and the amp works like a champ. It hits hard and clean. It depends on what your subs are rated for and what ohms they are.
  6. Alright I went to the website with all the details (actually multiple websites) and they didn't really give me what the actually sub displacement is in a box... but I did notice that they recommended 3 in diameter by 7.5 inches long for a port for EACH sub. The subs again are TS-W1008D4 Pioneer Premiers. Matt
  7. ok, just to make this clear and Im almost positive im doing it right...and this program is pretty nice btw...anyways when I enter my dimensions, it gives me a port area range...and leaves port area clear...and when i put dimensions in for the port, it gives me a port area.....now do i want that to get into that range? just clarifying.. and my subs are 10 inch...so would i jsut enter .1 (roughly) into the sub displacement?? thx matt
  8. Ok so I was playing around online and I found a calculator for ported boxes and get a basic idea and calculated some dimensions playing with numbers. BOX DIMENSIONS!!!! website: http://www.bcae1.com/spboxnew2.htm THIS IS FOR SINGLE PORT!!! Height = 18 inches Width = 25 inches Depth 1 (Top) = 13 inches Depth 2 (Bottom) = 19 inches Wood Thickness = 3/4 inches Speaker Displacement = .1 ft^3 (questionable) Port Freq. = 33 Hertz Port Diameter = 3.5 inches Number of Ports = 1 Sq. Port Ratio = 1:0.5 Box angle = 71.6 degrees Gross Box Volume = 3.154 ft^3 Net Box Volume = ft^3 Port length = 4.992 inches Port Area = 9.6 inches^2 Port Volume = .028 PORT: Height = 4.387 inches Width = 2.193 inches The only thing I am wondering, but almost 100% positive on is the Speaker Displacement. A 10 inch sub roughly displaces .05ft^3 so where it says questionable, do you just add the displacements together (so two subs like I want would equal .1 ft^3) Thanks for the help! Matt
  9. The subs are: Pioneer Premiers TS-W1008D4 here is the website: http://www.sonicelectronix.com/item_16648_Pioneer+Premier+TS-W1008D4.html *Unless you know of subs that are pretty much the same power for peak and RMS and about the same price* My trunk is roughly 4-5 from the backseat, to the rear of the car, about 4 feet wide by the back seat for 2 feet towards the back, and then opens up to about 5-6 feet in the last 2 feet. Its a 1997 Pontiac GP GT. I'm willing to look at any other subs that may be better, but again I dont have a lot of money, and the amp I have now I like a lot and it puts out 750RMS X 1 @ 1ohm stable. I havent had any problems with this amp, so I'm trying to build around it and make it have the best sound possible. Thanks!
  10. Hello. I am new to this forum and I just have a couple questions. I have been doing little (compared to the stuff I've seen on here and at competitions) installs in my own and just friends cars. I don't have the money for the big ass systems like some of you guys because I'm going to college and thats where my money is going. But that is besides the point. I would like to build a box for my new subs that I am going to get. Now, they say to use a sealed box for these but I've also seen ported and I have no idea what I should do. I know that ported tends to be on the louder side of things, but the sealed box will punch harder. The subs I want for a sealed box require 0.65-1.25 cubic feet for volume for EACH sub. But for ported, it is 0.9-1.55 cubic feet for EACH sub. Now my question(s) are: 1. What box should I make? In your honest opinion 2. If I were to do a ported box, what dimensions would I need to use (meaning the size of the box? The size of the port? Single port boxes or one double ported box?) 3.If it's in a trunk, would it even be worth to port the box? I'd like some input on this before I do anything. Thanks for your help! Matt
×
×
  • Create New...