[MA8's 4th order, 8th order, simple ported. Opinions wanted.]

That 4 th had way too small of a ratio.... hence why u cut it up

Think 2 cubes ported to 1 sealed minimum.... pr 3 ported 1 sealed

[dc 7.5 clamped]

Ill let him explain since I don't know the exact #s.....

Ray is an electrition by trade..... prollly knows more about electricity than 98% on this forum

[dc 7.5 clamped]

My numbers aren't right? I clamped over 8800 a amp at 14v rising to 1.3

You must not know what you're doing

Ya mite be right.. Lol.. Problem is I haven't blown a amp at .35 yet.. Must be the 3 alternators 10runs of 0g a 6 xs1400s.. Or maybe it's the $10 volt meter in my dash hooked up to my rear battery's that I watch like a hawk .. How you been bro?

Thats is Ray? thats all you got.

Ray doesnt know anything.... i only bug him with my questions for shitts and giggles

Txt me back fugger

[T-line or L port]

Tlines are musical setups not normally for the meter

I fuckin love my tlines!

[what is the eaisest way to identify a dc level 5 motor]

Lvl 5 m1 is 73lbs....... that is all

And has no tiny little vent holes..... the lvl5m2 has holes.... but no pole vent hole (the bigger hole)

That is no lvl 5!

Tell the guy who wants to trade to eat it....

[any difference in the btl n2's and n3's?]

N2s are bandpass freindly

N3s arnt

I love my n2s and I use them for SPL. They perform quite well, and id easily say they are the best subs I've ever owned!

[icecreaman feedback]

Sold him one of my 5ks

Great buyer very easy to work with....

Would sell to again in a flash....

thanks!

[DC M1 LVL 2 12 D4 and DC 1.2k *$250*]

You got a txt!!!

[any difference in the btl n2's and n3's?]

n2s are fuckin beast!!!!

[45s without table saw??]

[Hey guys, up for sale I have my tight (well use your imagination)! $750 OBO]

[2 DC 5k, 4 DC Level 4's]

Isnt this what i said

[2 DC 5k, 4 DC Level 4's]

Sounds like ur strapped but the rca isnt connected on the slave so you only clamping once amp

I got thoes exact same numbers with my 5ks then I plugged the strapped rca in and bam, 3500rms per amp.....

Make sure they are actually strapped.....

or try unstrapping them

2 5ks should be more than enough power for 4 lvl 4s, if u were getting upwards of 6k+ after rise ur subs will prolly get warm fast... just to much power for lvl 4s imot

But someone said it before more batteries too!

[01 Crown Vic]

I remember when my trunk looked like that.

Clever ipad mount!

[Opinions on which FI sub is best for my application please]

Get 12s

15s would be so hard to fit in there the sub is 15" but the basket is close to 16"

[Under 2g for 7k+]

american bass vlf 750,1....

dc 7.5k

[What about a 5000 watt system with this wiring.]

what are you talking about

thats how i do mine too

they hold

[Smelling coil? driving me nuts!]

Do it with the outside coil of each sub, try it

Then switch to the inside coil with both subs on one amp

That will show u if its the amp or the wiring

[Smelling coil? driving me nuts!]

Take all + and all - togetther to 1 amp for a .35 ohm load just to see if it works, then all subs should move the same

What's the box look like spects?

[Smelling coil? driving me nuts!]

Have u tried poping them yet?

Is it the same amp the one moving less both times?

Might be an amp issue causing the subs to work against each other, hence the smell..... mine did that at the beginning because one coil was wired wrong, havnt had a problem since and I run 5k to each so im pretty sure power to the sub isn't the issue

Is the phase on one amp off?

are the settings on the amp the same?

do you have a clamp meter can u clam each amp indivually?

Yes, I have a clamp (need some help on using it)

Both amps settings are identical, Phase is off on both amps (they are not strapped)

Yes I did a pop test for each coil. I held the neg wire on the nef of 9v and touched the pos and the cone moved out. I did that for all of them.

if they all poped the proper direction it seems like the amp... try what I sujested above with 1 amp to both subs to see if they will play the same, if they still do react the same ur wiring is off

[Smelling coil? driving me nuts!]

Try 1 amp to both subs see if they they play together fine if they do, there is a problem with ur amp

If they don't its ur wiring

^^^^ use the amp that u havnt had the issue with so we can baseline ur problem

That is the question we need answered it will show if its the amp or sub

[Smelling coil? driving me nuts!]

when 1 coil is out of phase but everything is wired up right, then one sub will move a lot less, still move in same direction sometimes but about 1/4 of the movement of the other....

It really seems like ur wired wrong.....

Are u wired series on the sub (+ to -) then the other + and - (from oppisite sides) going to the amp?

Check the series connection (+ to -) on the sub and made sure its not going + to + or - to -.... seemes stupied but I've done it.....

[Smelling coil? driving me nuts!]

Have u tried poping them yet?

Is it the same amp the one moving less both times?

Might be an amp issue causing the subs to work against each other, hence the smell..... mine did that at the beginning because one coil was wired wrong, havnt had a problem since and I run 5k to each so im pretty sure power to the sub isn't the issue

Is the phase on one amp off?

are the settings on the amp the same?

do you have a clamp meter can u clam each amp indivually?

[Smelling coil? driving me nuts!]

Do you have direct leads or push terminals

[Smelling coil? driving me nuts!]

If you havnt poped them you WILL NOT KNOW IF THEY ARE OR ARE NOT OUT OF PHASE

I seriously recommend you do this first with each sub

One sub probably isn't going to move out as much, that sub that doesn't is wired wrong!