shadowcaster Posted March 15, 2015 Author Report Posted March 15, 2015 ok so after doing my wifes truck with her single 8 it was time to get started on my civic.i took out the SA12s and got an X-15d2 also got and OM-1 some ABS plastic and a d680 for the rear 2000 blazer LS 240 mechman 2 b2 HN v3 15s crescendo bc5500 @.5 1/0 ebflex ofc d680/g31 kenwood deck mb quart components crescendo pwx 8s lots more to come blazer build http://www.stevemeadedesigns.com/board/topic/204432-shadowcasters-2k-blazer/ 142.8db MECA 2016 PA state champ mod 1 class
shadowcaster Posted March 15, 2015 Author Report Posted March 15, 2015 also got some more 1/0 ring,terminals,14ga,and some 10ga also put in a new H/U kenwood kdc-x397 have 2 sets of alpine sxe-1750 components .1 installed in the factory door location 1 to go in my kicks 2000 blazer LS 240 mechman 2 b2 HN v3 15s crescendo bc5500 @.5 1/0 ebflex ofc d680/g31 kenwood deck mb quart components crescendo pwx 8s lots more to come blazer build http://www.stevemeadedesigns.com/board/topic/204432-shadowcasters-2k-blazer/ 142.8db MECA 2016 PA state champ mod 1 class
shadowcaster Posted March 15, 2015 Author Report Posted March 15, 2015 after removing the SAs this was what i was left with so after some wire wheel and sanding i had 2000 blazer LS 240 mechman 2 b2 HN v3 15s crescendo bc5500 @.5 1/0 ebflex ofc d680/g31 kenwood deck mb quart components crescendo pwx 8s lots more to come blazer build http://www.stevemeadedesigns.com/board/topic/204432-shadowcasters-2k-blazer/ 142.8db MECA 2016 PA state champ mod 1 class
shadowcaster Posted March 15, 2015 Author Report Posted March 15, 2015 next i started on my spare tire well for fusing distribution and batt weather got bad so i decided to get the old rockfords out of the kicks and learned that the RF primes had a slightly bigger cut than the alpines 2000 blazer LS 240 mechman 2 b2 HN v3 15s crescendo bc5500 @.5 1/0 ebflex ofc d680/g31 kenwood deck mb quart components crescendo pwx 8s lots more to come blazer build http://www.stevemeadedesigns.com/board/topic/204432-shadowcasters-2k-blazer/ 142.8db MECA 2016 PA state champ mod 1 class
shadowcaster Posted March 15, 2015 Author Report Posted March 15, 2015 so i stripped the kicks bare used a cutout from a storage container lid the space was about an 1/8in so the plastic was just to fill in the gap...speaker is still screwed in the wooden ring i made 2000 blazer LS 240 mechman 2 b2 HN v3 15s crescendo bc5500 @.5 1/0 ebflex ofc d680/g31 kenwood deck mb quart components crescendo pwx 8s lots more to come blazer build http://www.stevemeadedesigns.com/board/topic/204432-shadowcasters-2k-blazer/ 142.8db MECA 2016 PA state champ mod 1 class
shadowcaster Posted March 15, 2015 Author Report Posted March 15, 2015 recovered with the velvet like it didnt happen lol 2000 blazer LS 240 mechman 2 b2 HN v3 15s crescendo bc5500 @.5 1/0 ebflex ofc d680/g31 kenwood deck mb quart components crescendo pwx 8s lots more to come blazer build http://www.stevemeadedesigns.com/board/topic/204432-shadowcasters-2k-blazer/ 142.8db MECA 2016 PA state champ mod 1 class
shadowcaster Posted March 15, 2015 Author Report Posted March 15, 2015 so i had good weather on saturday and got my mechman back in sorry for the picture quality pulled the alt bracket and wire wheeled it clean 2000 blazer LS 240 mechman 2 b2 HN v3 15s crescendo bc5500 @.5 1/0 ebflex ofc d680/g31 kenwood deck mb quart components crescendo pwx 8s lots more to come blazer build http://www.stevemeadedesigns.com/board/topic/204432-shadowcasters-2k-blazer/ 142.8db MECA 2016 PA state champ mod 1 class
shadowcaster Posted March 15, 2015 Author Report Posted March 15, 2015 how it looked when i started then ground down the ground spots and used dielectric grease on the bracket and grounds started to get dark so i went on to final placement of batt,fusing and distribution 2000 blazer LS 240 mechman 2 b2 HN v3 15s crescendo bc5500 @.5 1/0 ebflex ofc d680/g31 kenwood deck mb quart components crescendo pwx 8s lots more to come blazer build http://www.stevemeadedesigns.com/board/topic/204432-shadowcasters-2k-blazer/ 142.8db MECA 2016 PA state champ mod 1 class
shadowcaster Posted March 15, 2015 Author Report Posted March 15, 2015 but i learned that the covers for my fuse holders didnt like the 1/0 with heat shrink so i had to grind the plastic ends down a bit again picture quality sucks hope you can see 2000 blazer LS 240 mechman 2 b2 HN v3 15s crescendo bc5500 @.5 1/0 ebflex ofc d680/g31 kenwood deck mb quart components crescendo pwx 8s lots more to come blazer build http://www.stevemeadedesigns.com/board/topic/204432-shadowcasters-2k-blazer/ 142.8db MECA 2016 PA state champ mod 1 class
shadowcaster Posted March 15, 2015 Author Report Posted March 15, 2015 thats where i left off last night gotta go to pepboys for tires and an alignment while doing my alt i saw belts starting to show on my driver side inner tire so once i get back ill have the batt,fusing etc. installed and ready to move on to next project 2000 blazer LS 240 mechman 2 b2 HN v3 15s crescendo bc5500 @.5 1/0 ebflex ofc d680/g31 kenwood deck mb quart components crescendo pwx 8s lots more to come blazer build http://www.stevemeadedesigns.com/board/topic/204432-shadowcasters-2k-blazer/ 142.8db MECA 2016 PA state champ mod 1 class
Recommended Posts
Archived
This topic is now archived and is closed to further replies.