Jump to content

sayhuh?

18+ All Access!
 View Profile  See their activity

  • Posts

    3673

  • Joined

  • Last visited

 Content Type 

Posts posted by sayhuh?

  9. Circuit City $$$$$

    in Off Topic - Random, Misc posts - the forum "Junk Drawer"

    Posted · Edited by sayhuh?

    no i dont have any professional experience. thats why i guess i will say around 10- 11 buks an hour. I would be pissed after i get hired and then they shut down.

    Might as well as get pissed now. CC+bankruptcy+bad economy+bad Christmas sales due to the ecomony= LOTS of closures after Jan release of 4th quarter sales (or lack there of)

    Just a guess though :pardon:

    I'd take the job though...a job now is better than no job at all, plus you'll stay on for a while until they do close shop and then you have the install exp.

  10. When Ur Bass Over Powers The Mid-high U Need More Watts On The Door Speakers?

    in Mid's and highs

    Posted

    the only advice i can give on the amp question is u only need a 4ch when u got more than 4 speakers, if u got 4 speakers u could run a good 2ch amp n run it at 2ohm and get more power that a way cause most 4channel amps need to be down to 2ohm befor u get much power from them and the only diff between the few is u can adjust rears to be louder or what knot n u could fade from front to back, and if ur bass over powers ur mids n highs u either need to get rid of factory and get a good comp set and a good amp all u really need is a 2ch but if u want 4channel thats fine to btu it wont be as much efficent power tho that away and it would strain the amp to produce the wattage at 4ohm that it should do at 2ohm, but if ur mids n highs distort when u turn it up if u have to much bass goin threw mids n highs u'll more than likely get clipping if ur not giveing em enulf power, all i can think of is adjust ur bass/mid/treb on headunit to compinsate for the distortion, it helped my setup and i can go all the way to 40(full tilt) with out any distortion and if ur sla on headunit is past 0 it will get more distorted i got mine set to 0 so i can use more volume than rather have it louder at a lower volume, hope this helps

    :huh::blink::unsure:

    Umm..there are plenty of 4 channel amps that will do as much rms as a 2 channel..the 2 ohm thingy majiger confuses me too and not all decks have sla.

    Maybe I have been up way to laet, but nothing you said is making much sense to me.. :sad:-_-

    ----------------------------

    Basically, you need to get rid of fact speakers and do a good 2 or 4 channel amp (i'd prefer 4 but for fade and personal pref.) and have some adjust your shit right. Take it to a good local shop and have it done. Even ask them what to go with...granted they are going to try and sell you w/e, but at least it will sound right and hopefully good for w/e is in your budget. I hope dude above me was drunk when he typed that or I'm dog dick tired and it really makes sense later( 12 hour shifts, but its time to go home now).

    (not to be a dick..not meaning to offend) :8)

  11. Red Top Or Hc1800 For Coldweather Main Batt?

    in Electrical-battery- Alternators- Wiring

    Posted

    red top:

    http://www.autozone.com/R,2267985/vehicleI...oductDetail.htm

    720 cold cranking Amps (910 cranking Amps)

    kinetik hc1800:

    They dont list the CCA (that I found), but here ya go

    http://www.kinetikaudio.com/manuals/khccells.pdf

    1350 cranking amps...

    I'd say the HC1800., but at a cost of 50+ more (not including shipping on the HC1800).

    Money not an issue the choice is obvious. (buy two and ship one to me for helping you...if money isn't the problem) :friends:

  13. What To Use

    in General Audio - Can't find a category for your question? Ask here.

    Posted

    did you not read my post? just use the preouts on the amp/amps to go to other amp/amps

    ok, maybe I'm not looking at this right then, but if you have one set of RCA's coming out the deck and it goes into either a mono or 4 channel amp and these amps only have one output, wouldn't you still need a splitter?

    deck to mono, mono output to 4 channel...still need a splitter for the 4 channels (unless you want to run it 2 channel, which I don't).

    Deck to 4 channel...still the same problem...yes I can output to the mono with no probs, but still not wanting my mids at 2 channel.

    This is what I'm trying to get past...Speaker wire also not an option. Which is why I ask if an audio control three.1 or something would be my fix (EQ with line driver) or buy a different deck, but teh wifey would kill me :unknw:

    Not being a pain(i hope)..just want my 4 channel as a four channel...then again...I may be looking at it all wrong. mental pictures are > me ( a lot) =D

×
×
  • Create New...