-
Posts
140 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Media Demo
Store
Collections
Videos
Everything posted by bgaccord
-
thanks for the help guy's
-
where can i get 8" port ?
-
found the anwer box is 36w x 16h x20 deep,i was searching on google and it said i need 6sq of port per cubic feet if i use aero ports,with regular ports is 12-16sq so i need about 30",with one 6" is 28"sq,so i should be good,
-
well i build a box thats 5 1/2 cubic feet for my RE MT 18",i just want to know if i could get away with just 1 6" aero port, im asking because ,i check port calculator to see how long does 2 6" port have to be to get tuning @ 34 hertz and they have to be about 43" on each,thats too long
-
i need a 18" sub that can handle 3000watts,need a dual 2ohm,located near L.A for me to pick up
-
Symptoms?
bgaccord replied to imupabove's topic in Engine and Performance - Anything for that couple extra horses!
it can be you mass air flow sensor,thats what controls gas,buy one at junk yard because that part is expensive. -
3k rms on a single 12
bgaccord replied to IH8PunkRok's topic in Member Videos - Host 'em & Post 'em! System Vids / Off Topic
i have same amp ,love it,have it powering a aq 15 -
here what i have aq 15 hdc,powerbass xa3000,pionner600x4,alpine active xover,pioneer HU,cdt 6 1/2,diamond audio tweets. last time i meter i did a 145 with the rf t2000 with 4 gauge wire,i was broke to upgrade ,so know i have 0 gauge and 3000 watts ,got louder but really want to get meter. this are other sub i had 15 L7 10 L7 eclipse titanium 12
-
i check that to,it has lp hp and full ,so i have it in full, I really think is that piece of shi* amp,im going to get a powerbass 600.4 or 400.4 like the one in my sig to match my other amp and see what happens.
-
rca running from Hu to crossover is plug in on rca that have llabel FRONT ,and crossover has 3 outputs High,Low and sub so i have high for tweeters,low for mids and sub im not using
-
this is amp im running http://www.woofersetc.com/index.cfm?fuseac...product_id=2746 and this is crossover
-
this is how i have set up hook up HU--to crossover --2 rca's output one for highs and 1 for lows to amp
-
pioneer cant runs active.i check evething like 10x and still get distortion on mids only,tweets sound good.i dont know if the mids need more power.but im planning on getting a powerbass 600.4 amp
-
im runnnig active,i set gains with dmm but still get distortion,i think is 18db slope,i dont know how many real watts does the amp give out but it says 100 watts per channel so i have each speaker on its own channel i try setting crossover up to 180hz and still get distortion
-
well i have some cdt CL-61A-25 PRO components,i have them hook up with a dhd 400 watt amp and a alpine crossover ,when i turned it up my mids start distorting really bad,they dont get loud,my highs do ,but mids just distort,can it be the amplifier ?rigth now i have 2 channels for mids and other 2 channels for highs ,my mids are playing from 80 hz to 2500 and tweeter from 2500 and up.i play around with crossover but no luck
-
I wouldnt tuned them lower tham 35,i had my 15 tuned @34 with a 4 cube box and the sub would make noise,like it was bottoming out,so i build a 3.3 cubebox tuned at 38hertz and it get way louder and no more noises from sub