imupabove

where exactly did you buy this alarm? thank you.

should i get new ones? or wrench em out and then put them back in?

bump* its been a while since i cleaned the vacuum lines or use seafoam. whenever im at a full stop, that is when the stuttering occurs. it feels like the car is going to completely shut down. its pretty scary. i have a Stinger volt meter, and when it stutters the voltage drops. maybe alternator going bad? anyone have any clue what might be the cause of stuttering? thanks.

its a 1993 camry le 2.2 liters.

i did a master tune up (fuel filter, plugs, wires, pcv valve, and cap/rotor.) back in April.

hello people. dang havnt posted a topic in a while . i started my car today, my car started to feel like is was going to die out but then its alive. and it was idling pretty high than usual if i can remember. and when i accelerated it started to do it again (stuttering). i havnt checked the spark plugs b/c it was too dark. i replaced plugs and wires a couple of months ago. i will check out the plugs tomorrow. thanks for your time. bye.

bump should i even add this batt. to my system? will it do more harm than help for me? i really dont want to get a h/o alt for this car. thanks.

check this out.. im using a distributor block, it has 3 slots (0 gauge). from the front batt. goes into the distro. block, then the other 2 slots are for my mono amp and 4 channel amp. so do i put a fuse between the 2nd batt. and the distro. block? and how many amps should be the fuse. i hope im not confusing any of you people. thanks to all for the info.

do you recommend me fusing the hc600? would it be a good idea to ground my mono amp to the hc600? that is what i did to my amp and cap.

i just bought a hc600 battery. can someone please tell me how to hook this thing up. should i fuse it? where should i ground the battery? i bought this battery to replace my capacitor. thank you.

sorry to jack your thread but does upgrading to aftermarket battery terminals make a difference? if yes what are they? right now i just have the ring terminals on top of each other X\. thanks.

is that knu klm wire thick as the klmx wire?

so what should i do? my car is a 1993.

you know where they sell universal cats for my car that will pass emissions?

yeah a 150 amp and a good audio battery and im set. the most im going to ever run is 2k-3k but that is going to be later on. im only running 1500w tops.

i have a 1993 camry le 2.2L. a while back my cat converter was damaged and it made alot of noises when the car was on. so my mechanic welded a ordinary metal pipe replacing the old cat. will my car pass the smog test? am i loosing gas or any bad side effects that i just have a metal pipe on. thanks.

cool thanks. yeah im going to look into these alts. they have a 150 amp and a 220 amps for my car.

what kinda stock batt.? duralast? and you just have those caps too?

about like 130-xxx

bump can it be a bad distributor? their is gunk/build up on the dist. cap. its also getting on those sensors or plugs, not sure what are those and what they do :\. i bought new spark plug wires and spark plugs. so how would i know to change just the cap, the distributor itself, or the o-ring seal?

i really dont know where to start. can anyone help me please?

if it came down to it and i just get too lazy.. . what do you think about this box. i can get it for $140 shipped to me, maybe even a little cheaper.

not sure how to use that "port calc." on 12volt.com. what do i punch in? sorry kinda new at this.

have you heard about that RE calculator? should i use that to build my box? since you said "2.3 cu. ft.", do i times that by two?

hello. i have 2 alpine type r's. i want to make a ported box built for mainly spl but still maintain sound quality of course. i have no clue where to start. i have no tools except a drill and some handy tools. i messed around with that RE calculator but wasnt sure if i was things correctly, is it a useful tool? is that the only tool i need for my measurements and cut outs? should i double baffle it? im really serious on making this box, even though i never built one. i posted this same topic a while back but no success yet :[ but its cool. btw, i got a pair of 12" RF T1's and some day i want to use those with the same custom box. i want to build a universal ported box so any 12's will be loud in the box. thank you for your time. car:1993 camry sedan amp:rockford t10001bd trunk measurements: not yet taken