FiNaLaLmAsY

its my friends but thanks lol

yep hopefully woofers be in next week or so see how they sound

the angled pieces are to help loading on the back 2 woofers because they were so close to the port according do "DJSNT" good friend of mine does box designs and if it sounds bad i can pull them out. i was gonna use sonotube but the inner diameter on 8in sonotube is only like 7.1in! so i used 9in sewer pipe which i think it is and it had a decent flare lip and came out to like just shy of 8in inner diameter. its 18in in length with 5in external

Some updates today...for loading on the back woofers I added 2 "walls" 5in a piece with a round over of 1/4in. and added a middle 45 angled wall for a better frequency response.

ive built a lot of boxes before this is just a new build im doing from my old XXX 12s im going to be using truck bed liner and will be painting the port too. i build and seal all my boxes with PL Premium Advance and works better then anything else and if you buy the right stuff theres lots of different kinds the one i use helps reduce the amount of bracing needed.. i sealed the whole inside with the same glue i used for the box and i actually cut the hole smaller just slightly smaller then needed so its snug and beat the port in with a board on top and used a hammer to pound it in and checked for light to come out the other side. ive built aero port boxes before it is tuned correctly i was shooting for 35 so i did 34.5 according to torres because i added some extra bracing then what was figured on the calc to get closer to 35 i ended up running it through bassbox and came out to 35.2hz ish.. for now i also kept the rubber ring in there just so see maybe..if it helps or makes it worse it will be out eventually..

Hey all figure I would start posting more my builds on the Forum I just finished my new box for my 4 DD3500g 10's Coming in in the following week or two. 4 DD3500's 10's Flush Mounted, Tuned 34.5hz, 1.2cu per Woofer. This is my first box I ever Flush Mounted and didn't come out how i would have liked but i will test fit when they come in.. I used two 3in 45's in the back corners to direct the sound towards the port which might help and did a 2x2 brace in between both woofers. I might Truck bed liner my box to hide alot of my inperfections like the screws I should have made them a little more stright. But my guess this should pound and yes this is a trunk box port fired into the cabin.

okay how about this a kid i know named DJ designed me this with my max measurements of my trunk 4 10" Digital Designs 3500's Tuning: 34hz. Compression Chamber: 2.2 Cuft. per side Resp: 26hz. - 73hz.

just an idea... with 2 6in aeros fired into the cabin

or fire the subs up? and port out the side of the box

maybe i could fire 2 subs on each side of the car trunk for unloading and port into the cabin?

to me if i can find a way to stagger the subs on a 16 tall 36in wide face i would fire them from the trunk into the cabin and port out 6in out each side of the box into the trunk

3ft long? lol please tell me how that would be needed...because ive built plently of aero port boxes with torres box calc and bass box its not wrong

Hey all i just ordered 4 DD 3500g 10s Dual 4ohm Im building a box thats 15.5 tall 36 wide 23 deep 6.01cu each speaker will get almost 1.25cu a sub which is what DD told me.. im doing 2 6in pvc aero ports or 4 4in aeros i would like peoples inputs on that but 2 6in seems better port area... anyone recommend a good tuning to drop low and hit hard on the highs im thinking about 35-36hz tuned i will be giving them total about 5k rms... thanks!!

it was braced well and that is an illusion of the camera its very straight and lines up well i built a slot ported over year ago and never a issue the same way as this

its reinforced top and bottom with braces and 45s with the lid on i dont have pics of that.