whitetrash84

Andy 52761

I'm more than happy with my BTL N2. But if I were only going to run 1k I'd look at BL or Q depending on enclosure.

yeah my 15" BTL N2 will take my Sundown saz3000d no problem all day

Yeah just not sure about a kerf with a 2" radius. Might be kind of tight.

Also had thought about kerfing the 90s at the end, not sure if I got enough skills for that yet, lol

Yeah I was going to try a "v" and see if it does anything

Just wondering, with a slot port running down the middle and the branching off left and right at the back, does the width stay the same or is it 1/2 the width? I've always done 1/2 the width and now I'm not sure. So in my sketch-up the port shrinks to 3 1/8" at the back, or does it stay 6 1/4 on both sides:

The amp is a Behringher EuroPower 2400 and is now called the EuroPower 4000. Same amp just over rated now, think it's somewhere around $300-$350 now, I think I paid $280 in '06. I've clamped mine at 1200w @ 2ohm mono, it gets loud for a bedroom home theater set-up.

I've got 3 and 1/2 SA8 v1.5's. Bought one that needed reconed, then bought 2 more off a kid on CL in a pos ported box. Tried to order a drop in recone kit for the one from Jacob at sundown, he shipped me a complete freshly reconed sub for price of drop in recone and basket! So still have just the motor too! I build a .6cuft box tuned to 36 for the fresh recone. It doesn't compare at all to the btl, but I would say it compared to some of my past (late 90's) set-ups with dual 10"/12" on 400w or so. Pretty impressive. The v2's = beast!

I built this six years ago and decided I'd post it up here. This was about the 6th box I had made, knowing what I know now I would do a lot of things different but still happy with it. LoL I still haven't finished it, just sitting in bare mdf, someday I'll at least throw a coat of paint on it. Box is 12.5ft3 approx after displacement tuned via 8" sonotube port Subs are Soundsplinter RLP 15 d4's (tc based, I think 3hp?) Powered by a Behringher Europower ep2400 amp, clamped it and think it was close to 1200w Cramed it in a closet with subs firing back Lots of plaster patching on my 100 year old house! Thing pounds hard! Pics: Got Screws? 6 years later, surround got a little dry and grayish, I just rubbed a little armorall on the rubber and like new Rewired with some left over knu 8awg, the backs of the motors have oxidized too. Also I re-tuned it from 15hz to 28hz. cutting that tube out with a pocket knife was a bitch! Thinking flared 8" aero now.

Thx. It's a Sundown 3000d, the FI is a d1 it's hooked up 2ohms. I always though my headliner back there was loose until i realized the whole roof is moving that much. I though about going to a 18" but don't think the car will hold up. It's just slightly louder than my 12x2 type r's in a prefab on a pdx1.1000, LoL.

Re-worked my box a little, put some big 45s in three corners to take box from 5.3 cuft to 4.6ft and tuning from 29hz up to 32hz. Also resined the inside to seal it up good. Still need to do some vertical bracing, probably a couple of 2x2 or something. the resined 45s: box before: little window flex: Need better/more batteries and I'm going to go down to .5 ohm. Tried it with stock battery and dc power 270xp, voltage drops to 11's quick!

Just getting around to getting some of my stuff installed/finished. 15 BTL N2 d1 @ 2ohm for now on a SAZ-3000d. Box is 5.2ish ft3 @ 30hz 8" aero. Might do some additional bracing, maybe threaded rod or something. Mossy oak? in a Camry? Yep, lol! Will clean up the wiring once the 1/0 Knu goes in, this is still my old 4 knu from the last set up (2x12" type arghs and pdx 1.1000). Still need to do the other 2 pieces of the floor, waiting to see if I need additional battery before they get cut. Resolved my issuse with DC Power Engineering, got the correct harness and a spacer to put the 270 xp on. Very little voltage drop with the amp wired @ 2 ohm.

Yeah should be about 30"? And I've been kicking around the idea of sealing it off, but am going to go with the rear firing drivers side port for now, maybe when it's warmer out i'll try and build a new forward firing box and seal it off.

are there any pics or a build thread on this? I'd really be interested in seeing those. I think I'm going to build firing rear and port driverside box first and see how bad the trunk rattle is, then in spring try a forward box and seal it off.