Jordan Guess

do you put the inline resistor on the postiive or negative wire?

*bump* still need an answer to my most previous question, thanks!

alright thanks a bunch, and what would you call (high) for sensitivity? and that 4 0hm one with the 15 rms wouldn't be good then? even if my deck is only doing 17 rms per chan?

Sony-CDX-GT360MP

So I am struggling on choosing a tweeter that's going to fit my head units power capabilities, and if the ohm load that the tweeter is will majorly affect my vehicles audio performance. My favorite tweeter that I am looking at is 8 ohms, and RMS's at 50 watts with a 1300-20000 frequency range, but will this tweeter perform fully off my deck if its asking for 50 watts at 8 ohms? another tweeter RMS's at 15 ohms, but has a 4 ohm impedance with a 3500-25000 frequency range....would i be better off with this because it more matches the RMS wattage of my head unit? lastly, I found another tweeter that surpasses all others in that it is 4 ohms, but requires 100 watts RMS....would the power of my deck even be able to make two of these perform well? not to mention they are twice the price, and idk if i would want to do that If one of the 8 ohm tweets, or the low RMS 4 ohm tweet would better suite my needs. Also, at what frequency range will you no longer see in music? is 25000 a little over the top? or is it not enough?...your help is much appreciated, thanks! I avoided labeling titles of tweets so that I could avoid a vs. thread.

specs on em?

alright cool beans. that alpine MRP-2000 is being sold for $196.00 OTD on the contrary xD

so my DD 1508s would not like this thing lol? because it would be a final 4 ohm load...

^^^^? and is it 1 ohm stable?

preferably american made, or any of the key amps you see around this site. pm with price details, thanks!

any recommendations on what kind of super tweeters would even be a good place to start?

still got all this money....bump

Looking for any kind, let me know what you got. Thanks

Anyone got some good AMERICAN made 12" subs they are lookin to get rid of? Ive got a good budget and am also searching for an amp that will give them sufficient power. Looking to spend about $800. taking pm's or comments, thanks!

Im replacing the 5 1/4's in my friends 1999 Jeep Cherokee. 2 speakers are on the rear ceiling of the vehicle in the trunk and the other 2 are up front in the door panels. Im hoping for the rear of course to reach down into the lower frequencies and the front ones to go into the higher frequencies obviously. Can anybody point me in the right direction? Ive been looking at the Tang Band 5's for the rears but they are considered a woofer...will that not work well in a car audio system? IF anybody could point me in the right direction that would be great, my total budget is roughly $150. thanks for your help!

seal it off with?

Your vehicle flies??!?! I could get carriage bolts and most any local places? I.e: Ace hardware, walmart, kragen, and so forth?

So Im tired of seeing my wires run out the port of my box and I want to make it look cleaner. I remember seeing at one point at someones build look where they ran a bolt through the box and connected the speaker wire through both sides. It seems that copper is the cheapest and most conductive of metals, behind silver but that might be more expensive. Does anybody have any tips on how to wire this and what to use through 3/4 in. MDF board? your help is much appreciated thanks!

Some may think this is a ridiculous post but if anyone has either of these and are looking to get rid of them, PM me please. Edit: also willing to go with the non SE's (FT1's)

Yea but isn't a O-scope usually fairly expensive? Which one would I be using more per say if I was running a car audio shop and had people come in everyday and asking me to make there system sound better? This is is a hypothetical situation of course.

I'll be ordering two of these whenever they are ready. Are they specifically made for sealed only?

bump, could really use some advice here. I'm sure someone could use my well spent money on whatever device I need.

I was researching on this today and I have decided I want one, but I'm confused on what I NEED. Is the DD-1 considered an O-Scope? What is the difference? I just want to tune my system best as possible for a reasonable price while gaining more knowledge about SQ. your help is much appreciated. I feel like this is a vague post because I don't have a specified goal on what i'm looking exactly, I'm just hoping for some guidance. Thanks!

thanks a bunch guys! this all helps a lot especially the cutsheet post, and i figured it would handle around 2000 RMS because of the extra goodies i added to it. Is your wifes Fi Q the High QTS option? or just regular and what size of sealed box?

http://www.ebay.com/itm/180898507997?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649#ht_500wt_1413 SVC tho D=