808BommerN702

Level 6 M2 18" x2 89147

Ya, I was thinking to rotate the battery too, but even though the cables are insulated idk if that's a great idea...

Sorry KyLar...just needed help that's all

Ya, REAL96SS it's an amazing product. We are gonna have some unreal SPL and SQL systems out there more than ever cause of these products. I can't wait to see what SMD/D'AMORE will release next!!

Hey guys, Got a 2012 KIA Sorento V6 2wd and was wondering if I'll have a problem with a D3400 being installed. The battery will fit perfectly just the polarities are switched. Any suggestions???

IT WORKS!!!!!! YAAAAAAYYYYYYYY!!!! Ok, so this is what happened....First of all the orange arrow indicators are for the output signal, NOT for adjusting the EQ knobs on the amp/crossover. Secondly, I totally oversaw a surround feature that was hidden on my H/U. So guys that are about to buy a CC-1 please keep in mind that the arrows that point down and up is for OUTPUT SIGNAL ONLY!!! It's not for the crossover knobs. So there it is. Also if you have a SSF filter make sure that the track your playing is between the filter's indicators. My SSF filtered up to 30Hz. Stupid me was trying to play track #8 which is 31Hz. So the CC-1 wasn't calibrating because i was over on my SSF by 1Hz!! LOL!! Hope this helps guys! If you got any questions for me please respond back! Aloha!

This is what Juan said from d'amore "In regards to the arrows on the CC-1 they state what the output level should be adjusted to. With the infrasonic filter it is telling you to turn the pot until the output level decreases. With an infrasonic being a high pass filter you would have to turn it up in frequency to decrease the output signal. I know this is confusing but Please try setting up again, turning the frequency up and check if the CC-1 does tune your infrasonic filter. Please let us know if you need further assistance." Makes a whole lot of sense

Snowdrifter, I'm on my way home now. I'll get on my computer. How will I PM you?? Sorry I'm still new to the forum

Ya no problem. I'll try to post a video by Tuesday. I'll try too tonight though. Ya, I'll do that as soon as I can.

Ya I tried at 28Hz which was the highest cause the SSF cuts at 30Hz

No dog650 I try go to the very lowest volume that the CC1 reads a signal

It's an alpine MRX-M110. The ssf goes from 5Hz to 30hz. And I try to filter 25Hz. But it doesn't calibrate

No I did that out of frustration. I know what I did was wrong. That was just frustration. Do you know what the problem may be?? Cause it's kicking my ass. Any suggestions?

But ya "real" it's the volume that I'm talking about. Not anything else. I know that what I'm doing in that area is wrong.

Ya, but I know that's not how you do it. So I think it's turning it up on the subsonic that is going on. But idk. You have any ideas?

Ok, I emailed d'amore. Hopefully I get a response back today. But I highly doubt it. I just hope it's not the calibrator. Ugh. Thank you do very much duck for all your help!!! I really appreciate it!!

oh, i see what your asking, ok that's another thing. it gets a signal at around 12-17. but when i turn it down after reading it then it gives me the up arrow to calibrate. sorry

HU is at 26 undistorted. 27 is where it clips. the amp gain is under half way. totally distortion free! gotta love the DD-1!! Um, but ya you don't think the CC-1 is broken right? I honestly think my subsonic filter on the amp is shot. But ya man, i'd REALLY APPRECIATE IT if you could help me duck. thanks bro!

ok, 1. only the positive was unhooked 2. no sub fil. on the HU and no EQ between amp & HU. 3. HU was flat through N' through. no bass boost. But i do have a bass knob hooked to my amp. even that was turned all the way down as well. So should i unplug it?

Any other suggestions guys???

yup, tried both. still doesn't work. held down the off for 5 seconds. and turned it up while i turned it down. still fail.

i set my LPF to 80Hz successfully. so after that's set i can't adjust the sub fil. to 25Hz.

lowest freq on the LPF is 50Hz. the highest on the subsonic is 30Hz. idk what's going on.

let me rephrase my problem. Ok, first i turn my subsonic filter all the way down & my LPF all the way up. Then, I i go to my desired track which is track 16 (80Hz). i successfully calibrate my LPF. Then i turn off the cc1, turn my volume to 0. then as my sub filter still turned down all the way i then go to track 6 (25Hz) i then turn on the cc1, and slowly bring the volume up. i get a signal. then i hit read, and the cc1 is telling me to turn it down!!!! So am I doing something wrong? please help!! thanks!

i'm getting the same f!$#^ problem!!!!!! did you figure it out????