Bass4Lyfe Posted May 3, 2010 Report Share Posted May 3, 2010 If I had: (4) T1ks on (2) Duel 2 ohm subs I could wire each subwoofer to 1 ohm, then would I just wire 2 amps to that one sub? Like literally connect the speaker outputs to the same terminal on the box? Or should I put each amp to a voice coil? What's the protocol for this .. Would I pass-throiguh the RCAs? Thx ~Matthew 1998 Toyota Camry XLE V6 3L (1) ScyTek Astra 4000RS-2W-1 2-Way Remote Start Alarm with Shock and Proximity (1) 20% Tint All Around (Gately Audio) (1) 250 Amperage HO Alternator (1) Big 3 Done In 1/0 (2) Kinetik HC2400 Power Cell (1) Alpine IVA-D106 Receiver (1) Peripheral Video Bypass Device (4) Alpine SPS-17C2 Speakers (1) Alpine KCE-422i iPod Control Interface (4) Sheets Dynamat Extreme; for speakers (1) 10 Square Feet Hushmat (Trunk & Rear Deck) (4) DC Audio Level 4 15" D2 Subwoofer w/ Level 5 Coils (1) Wall Built By David, Tuned to 32 Hz (1) Rockford Fosgate T40001bd Amplifier (1) Stinger 1/0 Wiring (2 runs of + 2 runs of -) (1) Stinger Volt Meter Link to comment Share on other sites More sharing options...
dwright27 Posted May 3, 2010 Report Share Posted May 3, 2010 id run one coil per amp. you get more power that way and from what i was told by someone very very knowledgable this weekend, when you strap your amps you could clip without knowing it. get an oscope or dmm and gain match the amps. 2006 F-150 4 DC XL M2 18's Walled Daily Driver XS Power 4 DC 3.5kw Team DC Team S.P.L. Lot of Audio Technix and 1/0 DC Audio Dealer American Bass Dealer XS Power Dealer Audio Technix Dealer Link to comment Share on other sites More sharing options...
Bass4Lyfe Posted May 3, 2010 Author Report Share Posted May 3, 2010 Okay thanks man ... appreciate it ~Matthew 1998 Toyota Camry XLE V6 3L (1) ScyTek Astra 4000RS-2W-1 2-Way Remote Start Alarm with Shock and Proximity (1) 20% Tint All Around (Gately Audio) (1) 250 Amperage HO Alternator (1) Big 3 Done In 1/0 (2) Kinetik HC2400 Power Cell (1) Alpine IVA-D106 Receiver (1) Peripheral Video Bypass Device (4) Alpine SPS-17C2 Speakers (1) Alpine KCE-422i iPod Control Interface (4) Sheets Dynamat Extreme; for speakers (1) 10 Square Feet Hushmat (Trunk & Rear Deck) (4) DC Audio Level 4 15" D2 Subwoofer w/ Level 5 Coils (1) Wall Built By David, Tuned to 32 Hz (1) Rockford Fosgate T40001bd Amplifier (1) Stinger 1/0 Wiring (2 runs of + 2 runs of -) (1) Stinger Volt Meter Link to comment Share on other sites More sharing options...
dwright27 Posted May 3, 2010 Report Share Posted May 3, 2010 Okay thanks man ... appreciate it thats just my opinion and what id do though. i was told that by a guy doin 57's from 2 12's 2006 F-150 4 DC XL M2 18's Walled Daily Driver XS Power 4 DC 3.5kw Team DC Team S.P.L. Lot of Audio Technix and 1/0 DC Audio Dealer American Bass Dealer XS Power Dealer Audio Technix Dealer Link to comment Share on other sites More sharing options...
Bass4Lyfe Posted May 3, 2010 Author Report Share Posted May 3, 2010 shit that's loud no i appreciate it a lot. the dots were just like i was thinking trying to figure stuff out haha sorry didnt mean to be short i appreciate ur answer! ~Matthew 1998 Toyota Camry XLE V6 3L (1) ScyTek Astra 4000RS-2W-1 2-Way Remote Start Alarm with Shock and Proximity (1) 20% Tint All Around (Gately Audio) (1) 250 Amperage HO Alternator (1) Big 3 Done In 1/0 (2) Kinetik HC2400 Power Cell (1) Alpine IVA-D106 Receiver (1) Peripheral Video Bypass Device (4) Alpine SPS-17C2 Speakers (1) Alpine KCE-422i iPod Control Interface (4) Sheets Dynamat Extreme; for speakers (1) 10 Square Feet Hushmat (Trunk & Rear Deck) (4) DC Audio Level 4 15" D2 Subwoofer w/ Level 5 Coils (1) Wall Built By David, Tuned to 32 Hz (1) Rockford Fosgate T40001bd Amplifier (1) Stinger 1/0 Wiring (2 runs of + 2 runs of -) (1) Stinger Volt Meter Link to comment Share on other sites More sharing options...
ALPINE408 Posted May 3, 2010 Report Share Posted May 3, 2010 If I had: (4) T1ks on (2) Duel 2 ohm subs I could wire each subwoofer to 1 ohm, then would I just wire 2 amps to that one sub? Like literally connect the speaker outputs to the same terminal on the box? Or should I put each amp to a voice coil? What's the protocol for this .. Would I pass-throiguh the RCAs? Thx ^^^^^^^ doing what you said in bold would blow your amps the only way to hook up 2 amps to 1 sub is ether one to each coil or if the the amps can be strapped Have you ever had your woofers blown? Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.