cnate777

Im in...my build should be done by then

Trades? Pm me

4 cubes per sub with a slot port tuned to 32 hz just noticed that you are from florida. It wouldnt even be worth it.

whay kind of car is it goin in I have one for a yukon or suburban

This is what it looked like with a piece of 1/2 mdf underneath the carpet to mount them.

This is what it looked like with a piece of 1/2 mdf underneath the carpet to mount them.

I had 3 single farad caps on the trunk lid of my 2000 bonneville ssei it looked good however it was heavy as hell and the slightest little wind or bump would slam that trunk closed. That and until I readjusted my trunk tensioner I couldnt even get it to open with the keyless. It was a pain in the ass but it did look good. I have some pics that I will try and find and put them up on here.

Ive got a lightning audio 800.4 200x4. Great amp with box and everything

I am gonna do the port 10 by 10 by 14 which is gonna give me 32.46 hz i think that should do it does anyone know if fi will do a true dual 2 ohm voicecoil config or how my T20001bd's will act with a .7 load? Thanks everyone

do you have the dual 2 or 1. If you have the dual 2 how do the rockfords handle the .7 load

how does 10 by 10 by 14 for 32.46 hz sound

ok I think I am going to do a 10 x 10 x 10 port which gives me a tuning of 35.38 hz what does everyone think also that gives me 11.5 cubes after bracing and 45's. Does anyone think that will have port noise with that size port?

is there an equation to getting the tuning

What if I tune to 35hz and went to a slot port at the bottom of the box like 43.5 wide by 5 tall by ? 16ish

will that be ok even with the depth being 33 in.

I need some help I have 13.08 cubes of space with displacement im at 12.56. 45 wide by 33 deep by 18 tall. I need help with the port. The subs are going to face up and the port is going to face the rear. I was thinking about 144 sq in of port but not sure about how long to make it. I was think about 12 by 12 by ? I want to be at 32 hz I think. I would appreciate any help

My dimensions are 18 high by 45 wide by 33 deep for a total of 13.08 cubes. Just wondering what everyone recommends in regards to tuning and port dimensions?

you should need anything if you have the 530. are you doing it yourself? did the install manual come with the 530? what do you think you need a relay for?

anybody have any expereince with the superchips programmer

I guess everyone else is in the same boat and needing help with enclosures...dont forget me!!! HAHA

I used that program but there are some specifics that I am refering to. And I am not sure if that program is for T-line boxes. Anyone else that can help. I need someone that is versed in building boxes

I keep remembering all these things piece by piece but I am using 3/4 mdf what router roundover bit should I use 3/4 or 3/8 or another. Also is there one in particular I should use? tHANKS

Ok I keep seeing all these posts about T line boxes. These are my plans 2 18" BTL's. The space I have availbale is 45 wide 33 deep and 18 tall for a total of 13.08 cubes. Now from what I have read it looks like I need to have my frequency at 45 hz with theI would actually like to be down at 32 hz but I dont think that it wil work with the space that I have available. If that isnt right please tell me. Now with that said I believe that I need to have 480 sq in of port. I was planning on doing a port of 8x8x7.5 or 10x10x4.8 or 12x12x3.3 which would be better or is my 480 sq in of port completely wrong. I need help. Please

Thanks, right after i wrote on the forum I went to the website and saw it is .26. I have been looking at the 1/4 wave and T-line tutorial on the top of the subwoofer and enclosure section of the forum and if my math is right in order for me to be within my measurements of 18x45x33 and have enough cu ft i have to have a tune of 45 hz or so. Can anyone double check me?

does anyone know the displacement of a 18" BTL