sundownz

BOTH SOLD!!!

Regular - and I'll double layer it in most places.

I've used almost every deadener there is, including several rolls of Edead -- if I can afford it for a given project I would ALWAYS use Damplifier over anything else

If anything I'll have to buy more myself

Second Skin Damplifier - best stuff there is

Thanks Scottie

E-Mail is a little backed up right now... working on it.

This one is a uniform price pre-sale -- its the same until the pre-order is over.

The unmatched seats add 3 dB http://www.stevemeadedesigns.com/board/public/style_emoticons/default/hairtrick.gif

Getting those in and out of the box is a workout

Those are "Monster" prototypes

Uh oh... what is going on here ? Will be working on it some more tomorrow.

Pre-Order open as of now - be sure to get these while you can as I think the first run will go quickly. ETA is mid to late June for arrival of these woofers. As always, with a pre-order the ETA is subject to change based on shipping delays, etc, etc. PLEASE do not pre-order unless you are okay with any delays that may occur. Regular MSRP will be $239 dollars - right at our low 200s target Shipped prices in Continental 48 states -- contact me for AK and HI -- USA ONLY pre-order! Paypal me at [email protected] to pre-order. $175 shipped for ONE $330 shipped for TWO $620 shipped for FOUR Ask about more than that. Two of them in my Jeep has done up to 149.7 dB in a box that is too big with too much port area, so they have great SPL potential. Not only that - but they are GREAT sounding drivers with terrific low-end extension. They feature an aluminum shorting ring and a high linear x-max of 19mm one-way. RE: 7.09 ohms (D4 in series) Fs: 28.4 Hz Qes: 0.511 Qms: 5.75 Qts: 0.469 Vas: 40.3 L BL: 25.04 NA Le: 7.7 mH Mms: 252 g BL^2 / RE: 88 600 watts RMS Depth = 6.5" Cut-Out = 10 15/16" Enclosure Suggestions: 1.75 ft^3 ported tuned to 30 Hz -- F3 of 26 Hz * Tune higher for more SPL oriented setup * Enclosure can be as big as 2.25 ft^3 if you stick with the 600 RMS rating 1.00 ft^3 sealed -- F3 of 44 Hz * For SQ and space limited applications

Nightshades are out of stock -- updates will be posted when they are available again.

I changed my amp setup three times last week *laughs* Derrick is about like me in that regard.

I should add that I do still occasionally put them on the charger to make sure they are topped off

I have had great results using Harrison Labs Flux Capacitor voltage step-up modules to charge my 16v bank. They are 100-amps each so I use two to charge my bank at 17.9v (to be legal for all SPL organizations) to match my 200-amp alternator - and my 12v system is completer un-touched. The modules simply takes the 12v system input and outputs 17.9v (or whatever you tell them to set it at). Charging six PM D1000s this way for months now

Perhaps the OP simply had really bad luck - that is always a possibility as well I've had more than a few XS Power batteries (I'd say I've owned over 20 easily) and not a single issue for any reason no matter what kind of application I have put them in.

While we have you attention Scottie... when SHOULD you use the AGM High setting ?

I have TWO of the used amps available right now @ $675 each.

I still have one of them.

If you slam on it continuously at that power level it'll get a bit warm Should be fine as long as you aren't clipping the amps.