sundownz

$200 shipping $600 woofers --- $800 total

$60 + shipping each regardless of quantity Need to make room in the warehouse so price is 1/2 what I was originally asking. --- I bought out all of the QC failed SI BM 10s (old models) and re-built them with several changes: 1) Slightly longer flat-wound coil (original was round wire) - USA made coils 2) Narrower / Taller Surround 3) Tied down tinsel leads Measured T/S Specs (coils in series): RE: 6.89 ohms Z: 8 ohms Fs: 27.2 Hz Qes: 0.56 Qms: 3.32 Qts: 0.48 Le: 2.8 mH Vas: 31.1 L BL: 16.2 NA Mms: 124 grams Power: 400 watts RMS 0.95 ft^3 SEALED BOX - F3 of 41 Hz 1.5 ft^3 ported tuned to 30 - 35 Hz for high output I have about 40 of these... These are blow-out items and sold with no warranty beyond a no DOA guarantee. I can built re-cones for them for a while as I did get about 25 sets of extra parts! They are pretty tough with a 2.5" diameter flat coil, though. Nice sounding drivers.

FTW

Yah, there are several tests around -- here is one of mine : http://www.caraudio.com/forum/showthread.php?t=394409 2550 - 2640

Only 9 days to go

$400 for an SAZ-1500D until August 31st They are IN STOCK and ready to ship. My way of saying "thanks" to my customers over these past three years! This is the lowest price ever seen on the SAZ-1500D. Send me a Paypal to [email protected] with Note "SAZ-1500D SALE" OR Talk to your favorite Sundown dealer !!!

Pre-Order CLOSED. Amps due tomorrow.

Get some 1500s if that is what you want That is why the 1500Ds cost more -- they will handle stuff these wont.

No. These do not replace the SAZ-1500D. These amps do not have strapping, will not run over 15v, and were not made with the intent to run under 1 ohm. For a customer running 1 ohm on a 12v system these are an excellent amp.

One sold to Matt Crump

FS: Rockford Punch 501s - $200 OBO This amp has been tested on my bench and is guaranteed not to be DOA. No further warranty is expressed or implied. The item must be tested in no more than 5 days after receiving it -- do not e-mail me 2 weeks later... If you don't have the time or capability to test it within 5 days then don't buy here. Key Features Amplifier Type Dual Channel Bridgable Bridgable RMS Power at 4 Ohms 125 W x 2 RMS Power at 2 Ohms 250 W x 2 Performance Frequency Response 20 Hz - 20000 Hz Signal to Noise Ratio 100 dB THD at Rated RMS Power 0.05 % Crossover / Equalizer Bass Boost With Bass Boost Bass Boost Frequency 45 Hz Low - Pass Frequency 50 Hz - 250 Hz High - Pass Frequency 50 Hz - 250 Hz Other Features Input Voltage 14.4 volt MOSFET Circuitry Yes 3 Way Ready Yes Dimensions Width 12.07 in. Depth 9.85 in. Height 2.38 in.

FS: 2x Rockford T1500-1bd Power - $400 each OBO This amp has been tested on my bench and is guaranteed not to be DOA. No further warranty is expressed or implied. The item must be tested in no more than 5 days after receiving it -- do not e-mail me 2 weeks later... If you don't have the time or capability to test it within 5 days then don't buy here. These come with boxes and paperwork... no remotes. Number of Channels 1 Rated Power continuous power 500W x 1 @ 4-Ohms RMS 1000W x 1 @ 2-Ohms RMS 1500W x 1 @ 1-Ohm RMS Total Power total sum of 'rated power' 1500 Watts Bridgeable No Efficiency (average) 86% @ 4-Ohm 85% @ 2-Ohm 68% @ 1-Ohm Crossover Controls Low-Pass (LP): 35-250Hz 24dB/octave Butterworth Tone Controls Bass: 0dB to +18dB @ 45Hz Infrasonic Filter: -3dB @ 28Hz 12dB/Octave Signal Input Low level: 1 RCA pair Signal Output Low Level: 1 RCA pair Power Input Connector Block Power Wire Gauge 4 AWG Speaker Output Connector Screw terminal barrier strip Speaker Wire Gauge 8 AWG to 18 AWG Heat Sink Type Cast aluminum Cooling Convection Remote Controls Optional Remote Punch Bass EQ (overrides built-in Punch Bass EQ) Visual Indicators Power Thermal Protect Circuit Topology Class Class bd Frequency Response 20Hz to 250kHz +/- 0.5dB Shipping Weight 14.35 Lbs. (6.50 Kg.) Dimensions (HxWxL) 2.14 x 8.14 x 14.91 (in) 5.42 x 20.68 x 37.86 (cm)

PRE-SALE ORDERS ARE FINAL - THERE WILL BE NO REFUNDS -- If you are not 100% sure you will be financially stable then don't pre-order. No more exceptions. These amps are capable of a real 1500+ watts at 12.8 volts. They will out-perform many other 1500 watt rated amps (like the Audiopipe 1500) easily! ETA is the end of November. As always with a pre-sale there can be delays! COST ON PRE-SALE : AUGUST - $250 each SEPTEMBER - $260 each OCTOBER - $270 each NOVEMBER - $280 each PRICE IS SHIPPED IN CONTINENTAL 48 STATES. CONTACT ME ABOUT AK, HI, and international !!! The earlier you pre-order the lower the price will be. REGULAR price will be $350 MAP / $549 MSRP when in stock! PAYPAL me at [email protected] to take advantage of the pre-sale offer. Pre-sale will be closed on November 15th ! ---------- Externally it will look just like the old model SAE-1200D : Specs are also rated the same : SPECIFICATIONS: * 1200 x 1 watts @ 1 ohm * 600 x 1 watts @ 2 ohms * 300 x 1 watts @ 4 ohms * 0.153v - 5.6v adjustable input sensitivity * 15 Hz - 250 Hz Frequency Response * > 90 dB S/N Ratio * 4-Way Protection Circuit (Thermal, Overload, Speaker Short, and Over Current) * 50 Hz - 250 Hz adjustable 12dB Low-Pass Crossover * 15 Hz - 50 Hz adjustable 12dB Subsonic Filter * 0 or 180 degree adjustable phase switch * 0 - 12 dB adjustable bass boost with 60 Hz center frequency * Wired Remote Control unit included * 5x 30 Amp Internal Fuses * 17" L x 10.6" W x 2.2" H BUT the board is ALL NEW in design : Updates : 1) Double sided PCB board (v.1 was single sided) 2) More primary input caps 3) Large brass bars for power supply current 4) Revised layout 5) Superior Soldering and assembly quality TESTING vs. similar board to Audiopipe 1500 / 1800 : http://www.soundsolutionsaudio.com/forum/i...mp;#entry546813

I should add I am not looking to build these up -- if you want them built with these motors talk to Mike Bruno : http://www.caraudio.com/forum/showthread.php?t=419462

FS: Nightshade Motors (Blem) - $150 shipped Shipped price in continental 48 states. Most of these are new but with blemishes on the back plates. Some are used but in good shape. Add aluminum cooling plug for $25 installed. E-Mail me at [email protected] if interested.

Right.

Good job

It kind of sounds like the one sub was out of phase... did you notice it moving less than the other ?

Sending to [email protected] ?

I have a board that I believe to be equal to the new Audiopipe AP1800 model... as it is built just like the AP1500 but with two extra output FETs - I tested it vs. the SAE-1200D: For the sake of this test I just turned everything wide open just to see when they quit making power. THD was not a factor at all, just wide open. Obviously this is not the ideal situation -- I may send them to Chris so he can use some of his equipment to do a test using a scope as well. The amps are fed with a 4 awg and 8 awg wire in parallel reduced to 8 awg so it will fit both amps (the 1800 won't fit our 4 awg lead directly as it is tinned). Test load consists of two Nightshade 12s wire to 1 ohm and the tone is 60 Hz. ----- * SAE-1200D on the bench http://www.sundownaudio.com/misc/1800-watt...0D/CIMG2617.MOV * Power Test http://www.sundownaudio.com/misc/1800-watt...0D/CIMG2618.MOV * Output Voltage Test 1730 watts 59 V 29.3 A (calculated) 2.01 ohms (calculated) 12.68v power supply ----- 12x Power Supply Fets 10x Output FETs (AP1500 has The two caps = a little more capacity than the four in the AP1500D. These are 4700 each and the AP1500D has 4x 2200. * 1800-watt on the bench http://www.sundownaudio.com/misc/1800-watt...0D/CIMG2621.MOV * Power Test http://www.sundownaudio.com/misc/1800-watt...0D/CIMG2622.MOV * Output Voltage Test 1440 watts 57.1 V 25.21 A (calculated) 2.2 ohms (calculated) 13.1v power supply ----- SAE-1200D produced ~20% more power... and this 1800 has an extra 2 output FETs above the AP1500D. An SPL test may be more revealing... I may see if the 1800 will stay on in the Jeep at 1/2 nominal -- my rise is to just above 1 ohm.

Two of these will eat up an AP 3000.

Every SA-12 goes through this test before shipping to the customer. Lots of excursion

E-Mail me : [email protected]