Jump to content

crw092782

Members
 View Profile  See their activity

  • Posts

    204

  • Joined

  • Last visited

 Content Type 

Everything posted by crw092782

  1. crw092782

    Finished my door panels, now on to designing the box!

    1. JEFFYBOI

      JEFFYBOI

      You got a link? Mind if i check em out?

  2. crw092782

    I have most of the equipment in transit for the build.

  3. crw092782
    So you are the reason I can't order anything right now?
  4. crw092782
  5. crw092782

    Phase 2 complete. Head unit installed and the back doors complete.

  6. crw092782
    One other question... If I were to mount the subs Isobaric in this box, what would the extra space in the chamber do to the tuning?
  7. crw092782
    Nope! About an hour. When I get all done with everything I'll give you a demo.
  8. crw092782
    lbox.... Thank you so much!!! I got it out with that link! So happy right now. Thanks so much!!!!
  9. crw092782
    Thanks for trying Zack. Those are both for the Deville. It has a different dash setup than the Seville. :/ I think I am going to mess with it some more when I'm off of this conference call. If I still can't get it... I am going to just cut it out.
  10. crw092782
    Anyone have experience with this?
  11. crw092782
    I have been fighting with this for almost 2 hours now, and I about about to just break it off. lol.
  12. crw092782
    The problem I am having is that there isn't an actual ash tray there. It is just the plastic cubby, and the door that covers it. I have tried moving it back and forth, and up and down. It just won't budge.
  13. crw092782
    I am installing my double-din head unit in my 2003 Cadillac Seville and I can't get the ash tray out. I have searched for over an hour so far and haven't come up with anything that helps. The insert just will not come out. The worst part is that I can see the screw behind it that I need to remove to make the install happen. Any help would be greatly appreciated. Thank you.
  14. crw092782
  15. crw092782
    Ok thanks, I am going to just go ahead with these plans. I am just waiting for it to get a little warmer out here in Michigan and I can start building.
  16. crw092782
    Will this design have issues with the sub on the right unloading further back than on the port wall? Will I see any fault in this design?
  17. crw092782
  18. crw092782
    Good to know. I will leave it like that then. I am going to flush mount the subs though.
  19. crw092782
    Thank you so much! That is exactly what I was looking for. As soon as it gets warmer... I will be building this. I will probably 45 all of the corners though.
  20. crw092782

    Ready for the snow to melt so I can start installing this stuff in to the Caddy!

  21. crw092782
    My outside dimensions at 38 wide, 15 tall, 18.75 deep. I would like to tune the box in the low 30Hz range (29-33) but I have no idea how to figure in the port and tune it. I have always built sealed boxes or had someone else design the ported box for me and I built it to spec. I listen to a lot of Dubstep and Rap/hip-hop. This is my daily driver as well. The subs will be powered by a HiFonics Brutus 2100.1D. Thanks in advance for helping.
  22. crw092782
    I love Sonic Electronix! Welcome to the party!!!
  23. crw092782
    I just finished ordering a bunch of stuff for my build from Sonic. I can't wait to be able to rep you guys well.
  24. crw092782
    I ordered 2 pair of RCAs so I will just run them both back. I figure if I am already running one set... It wouldn't be hard to do 2 at the same time. (That's what she said)
  25. crw092782
    Should I be running 2 runs of RCAs from the HU to the trunk? Or can I use the "Output" of the MB Quart amp and put that on the sub amp?
×
×
  • Create New...