BassMunky

bump

i looked up EXfat wtf is that

which do i ust FAT or EXFAt? that all there is and the NTFS but people said not to use that

bump

i get that all the time lol

someone said Try FAT16 instead of FAT32 and never NTFS for a portable player how do i do that?

I have a problem? the thing is when I put songs on the Sansa memory it will play and find it on the deck (jvc-840), but when i put it on the sd card it wont find it when i play it on the deck it wont read the song. It will play the songs on the sd card on the mp3 player though. Any help? Mp3 player http://www.bestbuy.com/site/SanDisk+-+Sansa+Fuze%2B+4GB*+MP3+Player+-+Blue/2180714.p?id=1218312948870&skuId=2180714&st=sansa%20mp3&cp=1&lp=5

so my box is tuned to 35 hz do i set my ssf to 30 or 25hz? and set the lpf to 80hz right? now how do i know it at that exact setting? can i use this method with the car off or has to be on? Setting Subsonic Filter (SSF) Subsonic filter reduces the amplitude of certain frequencies depending on where it's set. If your using a sealed enclosure, then turn the ssf all the way counter-clockwise. So your enclosure is ported? Your going to set the ssf to the frequency your box is tuned to. Let's use 30hz as an example... disconnect speakers turn ssf counter-clockwise until it's considered "off" play 30hz tone at volume 10. Measure the voltage output Let y = voltage output * 0.707 turn ssf clockwise until voltage output now matches "y" Now your ssf is set. what would my voltage output be that i use? Setting Low Pass Filter (LPF) LPF does the exact same thing as the ssf but it's reducing higher frequencies that we don't want our speakers to play. Depending on the speaker your using and it's frequency response you'll want to set the lfp filter higher or lower then others. For this article were going to be setting it to 80hz for a subwoofer. disconnect speakers turn lpf clockwise until it's considered "max" play 80hz tone at volume 10. Measure the voltage output Let y = voltage output / 0.707> turn lpf counter-clockwise until voltage output now matches "y" Now your lpf is set

can i use this method to set the ssf and the lpf? Setting Subsonic Filter (SSF) Subsonic filter reduces the amplitude of certain frequencies depending on where it's set. If your using a sealed enclosure, then turn the ssf all the way counter-clockwise. So your enclosure is ported? Your going to set the ssf to the frequency your box is tuned to. Let's use 30hz as an example... disconnect speakers turn ssf counter-clockwise until it's considered "off" play 30hz tone at volume 10. Measure the voltage output Let y = voltage output * 0.707 turn ssf clockwise until voltage output now matches "y" Now your ssf is set. Setting Low Pass Filter (LPF) LPF does the exact same thing as the ssf but it's reducing higher frequencies that we don't want our speakers to play. Depending on the speaker your using and it's frequency response you'll want to set the lfp filter higher or lower then others. For this article were going to be setting it to 80hz for a subwoofer. disconnect speakers turn lpf clockwise until it's considered "max" play 80hz tone at volume 10. Measure the voltage output Let y = voltage output / 0.707> turn lpf counter-clockwise until voltage output now matches "y" Now your lpf is set

also one more thing is the manual window rollup handle how i stop that ratlling?

still it doesnt hit hard? what wrong? like when i play the on my level-wiz khalifa song it barely moves? how can i set the lpf and ssf? right now they are both set about half way?my gain is set good too when i had 2 10 before they slammed now they barely move with the 2 12

what would my cost be shipped to Hawaii if I use this? zip is 96813

help?

Audio Technix

How do i stop my window scissor that lift the door from rattling? I have deadner in the door and frame

where can i download it?

not to thread jack, but if you double up wire what does it compare too? let say you ran 2 runs of 12 gauge to the terminal what does that equal too?

yes it was the lpf was too low

only the gain is turned up half way everything else is 0

i did that the sub is on. like i said before the gain is halfway and sub still not moving there a signal like i said when i connect the rca to the amp

where the turn on sub setting on the deck?

what is it under?

running the jvc 840 deck to sundown saz 1200 amp 2 12 choas subs the subs dont even move everything is on and hooked up rigth is there a setting on the deck for the subwoofer on/off. I know everything is running right because when i plugged in the RCA ut nade a thump noise when rca touch amp inputs. soo any help would work. yes they are wired right the subs cause we just played it in another vehicle.