goinpro Posted November 30, 2007 Report Share Posted November 30, 2007 If I have a 2 channel amp...can I run one channel at 2 ohms and one channel at 4 ohms? 2005 Nissan Altima 2.5 S HU: AVIC-D2 Fronts: ARC Audio KAR KS6006 Components AA Poly Mids/ CDT CW-19 Tweets in kicks Front Amp: Profile AP400x2 Rear Fill: None Sub: DC LVL 4 (CF Dustcap) x2 (waiting for dustcaps) AMP: RF t10001bd x2 (1400-1500 @ 1 ohm) Wire: Welding Supply/Lighting Audio 1/0 Power/Ground Zero Noise 2.0zn RCA (x2) 260 Amp Iraggi Alternator Link to comment Share on other sites More sharing options...
dmanson Posted November 30, 2007 Report Share Posted November 30, 2007 If I have a 2 channel amp...can I run one channel at 2 ohms and one channel at 4 ohms? are the channels on the amp stable for 4 and 2 ohm? anyways what kinda setup are you trying to run? 2-DC 15XLM2 D.7s 1-DC 5K amp (1) XS Power D6500(UNDERHOOD) and (1) XS3000(REAR) 3 runs 1/0ga for power and 2 runs of 1/0ga for negative. (2)-RFT165s components, ...... 4 separate 1 inch tweetersRF T600-2(fronts) Punch 450.4(rear) Audiocontrol 3.1. DC power 260amp alternator w/MLA Module Link to comment Share on other sites More sharing options...
Decaf Posted November 30, 2007 Report Share Posted November 30, 2007 if the amp is 2 ohm stable, sure Link to comment Share on other sites More sharing options...
dmanson Posted November 30, 2007 Report Share Posted November 30, 2007 now don't go hooking up two alike subs ......... one being 4 ohm and the other 2 ohm up to that 2 channel amp. the 2 ohm sub will see more power and play slightly louder than the 4 ohm sub ........... just my advice if that is where this thread is going to lead. 2-DC 15XLM2 D.7s 1-DC 5K amp (1) XS Power D6500(UNDERHOOD) and (1) XS3000(REAR) 3 runs 1/0ga for power and 2 runs of 1/0ga for negative. (2)-RFT165s components, ...... 4 separate 1 inch tweetersRF T600-2(fronts) Punch 450.4(rear) Audiocontrol 3.1. DC power 260amp alternator w/MLA Module Link to comment Share on other sites More sharing options...
goinpro Posted November 30, 2007 Author Report Share Posted November 30, 2007 no i havent done anthing yet. Im just trying to figure out what I want to do. It would not be for subs but more mids and highs. It would be with a RF t5002. I was wondering if I could run one channel at like 1 ohm for my mids and another at 2 ohm for my tweets 2005 Nissan Altima 2.5 S HU: AVIC-D2 Fronts: ARC Audio KAR KS6006 Components AA Poly Mids/ CDT CW-19 Tweets in kicks Front Amp: Profile AP400x2 Rear Fill: None Sub: DC LVL 4 (CF Dustcap) x2 (waiting for dustcaps) AMP: RF t10001bd x2 (1400-1500 @ 1 ohm) Wire: Welding Supply/Lighting Audio 1/0 Power/Ground Zero Noise 2.0zn RCA (x2) 260 Amp Iraggi Alternator Link to comment Share on other sites More sharing options...
joey2714 Posted November 30, 2007 Report Share Posted November 30, 2007 i ran my T15004 like that for a while never had any problems play Moola.com its actually fun and free... click here to join Money games! its just games with free money! Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.