DODGE-BASSHEAD25 Posted February 13, 2012 Author Report Share Posted February 13, 2012 65.1 and 24.9 respectively (the complement divided by two for the cuts), the problem with that design is that the internal volume is way above BA uses, around 3.1 cubic feet, most likely overexcursion will result at or below rated power. So I guess there is no choice but to go balls to the wall and go for the "V" and learn from my mistakes. Could I get the dimension on those braces and also how much wide should the rings be. I know 3/4" thick obviously but ow wide. Car 1999 Dodge Stratus 2.5L V6 Deck Kenwood DDX-512 Head Unit Doors (2) Diamond Audio DA6.6 6.5's (2) Cerwin Vega 3" Horn Tweeters (1) Alpine MRP-F240 for Doors & Tweets Rear Deck(on factory wiring) (2) JVC 6.5's (2) Rockford Fosgate 6x9's Subs firing forward (2) Skar Audio VVX-12's (1) MBQuart ONX1500.1D for Subs Wiring Cadence 4AWG for MBQuart Amp Advance Auto 8 AWG for Alpine Amp Cadence and Monster 4 AWG Wire to Kinetic HC1200 Batteries Stock Replacement up front Kinetic HC1200 in the back for the amps. And yes "I drive a Dodge Stratus" Here is my build log: http://www.stevemead...__fromsearch__1 Link to comment Share on other sites More sharing options...
Joe X Posted February 13, 2012 Report Share Posted February 13, 2012 Ok so I rechecked everything and couldn't find any issues, the rings should have an internal diameter same as the hole on the baffle and an external diameter same as the external diameter of the sub, the brace dimensions are as follows: Link to comment Share on other sites More sharing options...
DODGE-BASSHEAD25 Posted February 13, 2012 Author Report Share Posted February 13, 2012 ok cool. so the rings will be the same as the outside diameter of the sub? not the mounting diameter? Car 1999 Dodge Stratus 2.5L V6 Deck Kenwood DDX-512 Head Unit Doors (2) Diamond Audio DA6.6 6.5's (2) Cerwin Vega 3" Horn Tweeters (1) Alpine MRP-F240 for Doors & Tweets Rear Deck(on factory wiring) (2) JVC 6.5's (2) Rockford Fosgate 6x9's Subs firing forward (2) Skar Audio VVX-12's (1) MBQuart ONX1500.1D for Subs Wiring Cadence 4AWG for MBQuart Amp Advance Auto 8 AWG for Alpine Amp Cadence and Monster 4 AWG Wire to Kinetic HC1200 Batteries Stock Replacement up front Kinetic HC1200 in the back for the amps. And yes "I drive a Dodge Stratus" Here is my build log: http://www.stevemead...__fromsearch__1 Link to comment Share on other sites More sharing options...
Joe X Posted February 13, 2012 Report Share Posted February 13, 2012 ok cool. so the rings will be the same as the outside diameter of the sub? not the mounting diameter? 9 1/4 inner (same as the cutout on the baffle) 10 1/2 outer. Link to comment Share on other sites More sharing options...
DODGE-BASSHEAD25 Posted February 13, 2012 Author Report Share Posted February 13, 2012 ok cool. so the rings will be the same as the outside diameter of the sub? not the mounting diameter? 9 1/4 inner (same as the cutout on the baffle) 10 1/2 outer. Ok. Hopefully gonna start it this week. Will definitely be done by the end of next week. Hoping to have it in and bumpin by next Sunday Car 1999 Dodge Stratus 2.5L V6 Deck Kenwood DDX-512 Head Unit Doors (2) Diamond Audio DA6.6 6.5's (2) Cerwin Vega 3" Horn Tweeters (1) Alpine MRP-F240 for Doors & Tweets Rear Deck(on factory wiring) (2) JVC 6.5's (2) Rockford Fosgate 6x9's Subs firing forward (2) Skar Audio VVX-12's (1) MBQuart ONX1500.1D for Subs Wiring Cadence 4AWG for MBQuart Amp Advance Auto 8 AWG for Alpine Amp Cadence and Monster 4 AWG Wire to Kinetic HC1200 Batteries Stock Replacement up front Kinetic HC1200 in the back for the amps. And yes "I drive a Dodge Stratus" Here is my build log: http://www.stevemead...__fromsearch__1 Link to comment Share on other sites More sharing options...
DODGE-BASSHEAD25 Posted February 13, 2012 Author Report Share Posted February 13, 2012 Just to check this is what I need right? Top and bottom: 36 x 18 1/2" Sides: 14 1/2 x 18 1/2 Back: 14 1/2 x 22 9/16 Two MDF rings for mounting the outer subs Car 1999 Dodge Stratus 2.5L V6 Deck Kenwood DDX-512 Head Unit Doors (2) Diamond Audio DA6.6 6.5's (2) Cerwin Vega 3" Horn Tweeters (1) Alpine MRP-F240 for Doors & Tweets Rear Deck(on factory wiring) (2) JVC 6.5's (2) Rockford Fosgate 6x9's Subs firing forward (2) Skar Audio VVX-12's (1) MBQuart ONX1500.1D for Subs Wiring Cadence 4AWG for MBQuart Amp Advance Auto 8 AWG for Alpine Amp Cadence and Monster 4 AWG Wire to Kinetic HC1200 Batteries Stock Replacement up front Kinetic HC1200 in the back for the amps. And yes "I drive a Dodge Stratus" Here is my build log: http://www.stevemead...__fromsearch__1 Link to comment Share on other sites More sharing options...
Joe X Posted February 13, 2012 Report Share Posted February 13, 2012 Top and bottom: 36 x 18 1/2" Sides: 14 1/2 x 18 1/2 Back: 34 1/2 x 14 1/2" 2 x Baffle: 14 1/2 x 22 9/16 50 deg cuts. ( to make sure you have enough material for rhe angled cuts make it 24) 2x Ring: 9 1/4 inner - 10 1/2 outer. 2x Brace: 10 x 4 Link to comment Share on other sites More sharing options...
DODGE-BASSHEAD25 Posted February 13, 2012 Author Report Share Posted February 13, 2012 Top and bottom: 36 x 18 1/2" Sides: 14 1/2 x 18 1/2 Back: 34 1/2 x 14 1/2" 2 x Baffle: 14 1/2 x 22 9/16 50 deg cuts. ( to make sure you have enough material for rhe angled cuts make it 24) 2x Ring: 9 1/4 inner - 10 1/2 outer. 2x Brace: 10 x 4 Ok. I had it written down different but must've messed up when typing. Lol. Again thanks for all your help Joe I will definitely post pics during the build and when it's done. Car 1999 Dodge Stratus 2.5L V6 Deck Kenwood DDX-512 Head Unit Doors (2) Diamond Audio DA6.6 6.5's (2) Cerwin Vega 3" Horn Tweeters (1) Alpine MRP-F240 for Doors & Tweets Rear Deck(on factory wiring) (2) JVC 6.5's (2) Rockford Fosgate 6x9's Subs firing forward (2) Skar Audio VVX-12's (1) MBQuart ONX1500.1D for Subs Wiring Cadence 4AWG for MBQuart Amp Advance Auto 8 AWG for Alpine Amp Cadence and Monster 4 AWG Wire to Kinetic HC1200 Batteries Stock Replacement up front Kinetic HC1200 in the back for the amps. And yes "I drive a Dodge Stratus" Here is my build log: http://www.stevemead...__fromsearch__1 Link to comment Share on other sites More sharing options...
Joe X Posted February 13, 2012 Report Share Posted February 13, 2012 Ok, just work slowly and to detail, is not as hard as it looks. If you have any questions ask, there are a number of tutorials on box building watch a couple of them..luck. Link to comment Share on other sites More sharing options...
DODGE-BASSHEAD25 Posted February 13, 2012 Author Report Share Posted February 13, 2012 Thanks for the luck. And the angles are 100 in the middle divided into two 50s and 40 on the sides right. Car 1999 Dodge Stratus 2.5L V6 Deck Kenwood DDX-512 Head Unit Doors (2) Diamond Audio DA6.6 6.5's (2) Cerwin Vega 3" Horn Tweeters (1) Alpine MRP-F240 for Doors & Tweets Rear Deck(on factory wiring) (2) JVC 6.5's (2) Rockford Fosgate 6x9's Subs firing forward (2) Skar Audio VVX-12's (1) MBQuart ONX1500.1D for Subs Wiring Cadence 4AWG for MBQuart Amp Advance Auto 8 AWG for Alpine Amp Cadence and Monster 4 AWG Wire to Kinetic HC1200 Batteries Stock Replacement up front Kinetic HC1200 in the back for the amps. And yes "I drive a Dodge Stratus" Here is my build log: http://www.stevemead...__fromsearch__1 Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.