wwjm Posted March 23, 2012 Report Share Posted March 23, 2012 two amps is better than one for many reasons one of my personal reasons is if something was to go wrong with the amp and your not financially able to deal with it right away than your out in the cold on sub action with two you'll always have a way to listen to ya subs unless something goes wrong with both plus more power for later if you upgrade subs or add too what you got it just keeps more options available as far as performance they'll be no major difference in it really sell and get you two that r 1ohm stable for the future Quote Link to comment Share on other sites More sharing options...
G-Rad Posted March 24, 2012 Report Share Posted March 24, 2012 2 Dual 4 Ohms can wire to 1 ohm. If you can sell one of your 1000.1's for 300, then you have more than enough to pick up an AQ1200D, which does 1200WRMS at 1Ohm. Quote BASS MEKANIK RECORDS "Audio Implosion" & "SubSonic Guillotine" available anywhere digital music is sold! 2007 Ford Focus (NOTE: My cousin's build I helped him with) Pioneer H/U (4) Absolute Dome Tweeters on A & C pillars Scosche HD683A's in front doors Fosgate R168x2's in rear doors SoundQubed HDS312 in custom 2.57 Ft^3 @ 30Hz Audiopipe APCL-1800.1D Q-Mat Audio Technix 0 Gauge 119aH/850CCA Marine Deep Cycle batteries YouTube Channel: http://www.youtube.com/DWRhythm Link to comment Share on other sites More sharing options...
Watch the bass Posted March 24, 2012 Report Share Posted March 24, 2012 2 Dual 4 Ohms can wire to 1 ohm. If you can sell one of your 1000.1's for 300, then you have more than enough to pick up an AQ1200D, which does 1200WRMS at 1Ohm. OMG Quote "in the abundance of water, the fool is thirsty" Bob Marley Link to comment Share on other sites More sharing options...
Robbie Dee Posted March 24, 2012 Report Share Posted March 24, 2012 I have a DC1.2k 1 ohm stability in this Audi A6 pushing 2 dual 4 ohm DClvl3 12's. I wired the subs down to 1 ohm as in diagram. Now that everything is hooked up what do i do w my Amp to get the deepest loudest low frequency bass possible? i would really apprectiate any help on setting my gains. Sub nd Amp Info. thanxx SUB Info 10" 12" 15" 18" Mounting Depth 6.25" 6.75" 8" 9.5" Mounting Hole Diameter 9.35" 11" 14" 16.75" Outside Driver Diameter 11" 12.5" 15.7" 18.5" Motor Width 7" 7" 7" 7" Weight 20lbs 20.5lbs 21.5lbs 22lbs VC Diameter 3" 3" 3" 3" Displacement .15³ ft .16³ ft .18³ ft .22³ ft Magnet Weight 18lbs 18lbs 18lbs 18lbs Power Handling RMS/Peak 900/1800 900/1800 900/1800 900/1800 Impedance (Ohm) D1/D2/D4 D1/D2/D4 D1/D2/D4 D1/D2/D4 Sd 324cm² 481cm² 823cm² 1217cm² Vas 13.16 liters 28.99 liters 84.88 liters 185.6 liters Cms 0.09 mm/N 0.09 mm/N 0.09 mm/N 0.09 mm/N Mms 190 g 225 g 295 g 305 g Fs 38.5 35.4 30.9 30.4 BL 17.2 N/A 17.2 N/A 17.2 N/A 17.2 N/A Re 3.6 Ohm 3.6 Ohm 3.6 Ohm 3.6 Ohm Le 3.5 mH 3.5 mH 3.5 mH 3.5 mH Qms 7.66 8.33 8.18 8.32 Qes 0.567 0.617 0.706 0.718 Qts 0.528 0.574 0.65 0.661 Xmax 23 mm 23 mm 23 mm 23 mm Ref SPL @ 1 watt 83.1 dB ([email protected]) 85 dB ([email protected]) 87.3 dB ([email protected]) 90.4 dB ([email protected]) Suggested Sealed .65³ ft 1³ ft 2³ ft 4³ ft Suggested Ported 1³ ft 1.5³ ft 3³ ft 6³ ft AMP Info Key Features • 1 ohm stable • Variable low pass filter • Variable subsonic filter • Variable bass boost • Wired remote control We recommend for installation • 1 upgraded battery under the hood • Dash mounted voltage meter Features Voltage 1.2kw Output Power (RMS) 4 ohm 14.4V 350W x 1 2 ohm 700W x 1 1 ohm 1,200W x 1 1 ohm 16V 1,450W x 1 1 ohm 18V No Input Sensitivity 6V~0.2V Low Pass Filter Switchable ( @ 24 dB Slope) Variable Hz 35~250 Subsonic Filter Switchable ( @ 24dB slope ) Variable Hz 10~50 Bass Boost Variable dB 0-9dB Frequency Response Hz 15-270 Signal to Noise Ratio dB 100 Damping factor 100< Efficiency @ 4ohm % 81% THD @ 4ohms Less than 0.1% Fuse Rating 120 Amps Linked Fuse Rating 240Amps Indicator Power Yes Protection Yes Clip no Speaker & Power terminal Mold Type Yes Power Gauge 4Ga Heatsink Length inch/mm 11.81"/300mm Heatsink Width inch/mm 9.38"/238mm Heatsink Height inch/mm 2.35"/59.6mm Quote Link to comment Share on other sites More sharing options...
armykyle1 Posted March 24, 2012 Report Share Posted March 24, 2012 I have a DC1.2k 1 ohm stability in this Audi A6 pushing 2 dual 4 ohm DClvl3 12's. I wired the subs down to 1 ohm as in diagram. Now that everything is hooked up what do i do w my Amp to get the deepest loudest low frequency bass possible? i would really apprectiate any help on setting my gains. Sub nd Amp Info. thanxx SUB Info 10" 12" 15" 18" Mounting Depth 6.25" 6.75" 8" 9.5" Mounting Hole Diameter 9.35" 11" 14" 16.75" Outside Driver Diameter 11" 12.5" 15.7" 18.5" Motor Width 7" 7" 7" 7" Weight 20lbs 20.5lbs 21.5lbs 22lbs VC Diameter 3" 3" 3" 3" Displacement .15³ ft .16³ ft .18³ ft .22³ ft Magnet Weight 18lbs 18lbs 18lbs 18lbs Power Handling RMS/Peak 900/1800 900/1800 900/1800 900/1800 Impedance (Ohm) D1/D2/D4 D1/D2/D4 D1/D2/D4 D1/D2/D4 Sd 324cm² 481cm² 823cm² 1217cm² Vas 13.16 liters 28.99 liters 84.88 liters 185.6 liters Cms 0.09 mm/N 0.09 mm/N 0.09 mm/N 0.09 mm/N Mms 190 g 225 g 295 g 305 g Fs 38.5 35.4 30.9 30.4 BL 17.2 N/A 17.2 N/A 17.2 N/A 17.2 N/A Re 3.6 Ohm 3.6 Ohm 3.6 Ohm 3.6 Ohm Le 3.5 mH 3.5 mH 3.5 mH 3.5 mH Qms 7.66 8.33 8.18 8.32 Qes 0.567 0.617 0.706 0.718 Qts 0.528 0.574 0.65 0.661 Xmax 23 mm 23 mm 23 mm 23 mm Ref SPL @ 1 watt 83.1 dB ([email protected]) 85 dB ([email protected]) 87.3 dB ([email protected]) 90.4 dB ([email protected]) Suggested Sealed .65³ ft 1³ ft 2³ ft 4³ ft Suggested Ported 1³ ft 1.5³ ft 3³ ft 6³ ft AMP Info Key Features • 1 ohm stable • Variable low pass filter • Variable subsonic filter • Variable bass boost • Wired remote control We recommend for installation • 1 upgraded battery under the hood • Dash mounted voltage meter Features Voltage 1.2kw Output Power (RMS) 4 ohm 14.4V 350W x 1 2 ohm 700W x 1 1 ohm 1,200W x 1 1 ohm 16V 1,450W x 1 1 ohm 18V No Input Sensitivity 6V~0.2V Low Pass Filter Switchable ( @ 24 dB Slope) Variable Hz 35~250 Subsonic Filter Switchable ( @ 24dB slope ) Variable Hz 10~50 Bass Boost Variable dB 0-9dB Frequency Response Hz 15-270 Signal to Noise Ratio dB 100 Damping factor 100< Efficiency @ 4ohm % 81% THD @ 4ohms Less than 0.1% Fuse Rating 120 Amps Linked Fuse Rating 240Amps Indicator Power Yes Protection Yes Clip no Speaker & Power terminal Mold Type Yes Power Gauge 4Ga Heatsink Length inch/mm 11.81"/300mm Heatsink Width inch/mm 9.38"/238mm Heatsink Height inch/mm 2.35"/59.6mm are you serious with this fucking post? GTFO... To the op, Sell em, get a saz2500 or similar... Not a AQ1200 lol Quote TEAM XS POWERTEAM HEAVY HERTZMy build- http://www.stevemeadedesigns.com/board/topic/194454-e46-bmw-build-pos/#entry2914134youtube- http://www.youtube.com/user/armykyle1big build starting Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.