Cardboardcat15 Posted April 21, 2012 Author Report Share Posted April 21, 2012 You fix your trunk yet? Looking nice btw Nope, not yet at least. That's on the agenda for tomorrow. My Channel on YouTube. Check it out for cinematic-style Car Audio videos. https://www.youtube.com/channel/UCcSMhtT-rpopJbdybubDgnQ New 2014 Scion TC 4th Wall Build https://www.stevemeadedesigns.com/board/topic/217173-2014-tc-4th-order-build-3-fi-sp4-15s/ Link to comment Share on other sites More sharing options...
Cardboardcat15 Posted April 24, 2012 Author Report Share Posted April 24, 2012 K, did a little more yesterday. I'm really bad a taking pictures, so here's what I got. Where the batt will go Yanked the old wire out Fused DC 2K bass knob which currently goes bananas every time it's plugged in Spaghetti, anyone? Temp setup till my recones get here. That's all for now, Orionstang is comin over tomorrow to DD-1 the 2K and HOPEFULLY fix the bass knob issue. The clip light stays on constantly, even when the RCA's aren't plugged in. Dafuq. My Channel on YouTube. Check it out for cinematic-style Car Audio videos. https://www.youtube.com/channel/UCcSMhtT-rpopJbdybubDgnQ New 2014 Scion TC 4th Wall Build https://www.stevemeadedesigns.com/board/topic/217173-2014-tc-4th-order-build-3-fi-sp4-15s/ Link to comment Share on other sites More sharing options...
Joeym4692 Posted April 24, 2012 Report Share Posted April 24, 2012 Looking good so far! Can't wait to see progress with this one Link to comment Share on other sites More sharing options...
Cardboardcat15 Posted April 24, 2012 Author Report Share Posted April 24, 2012 Also, the wet par of my undercarraige is tranny fluid. Mechanic said it had to have been leaking for a really long time for it to get that far down. Not a big deal. My Channel on YouTube. Check it out for cinematic-style Car Audio videos. https://www.youtube.com/channel/UCcSMhtT-rpopJbdybubDgnQ New 2014 Scion TC 4th Wall Build https://www.stevemeadedesigns.com/board/topic/217173-2014-tc-4th-order-build-3-fi-sp4-15s/ Link to comment Share on other sites More sharing options...
Guest Posted April 24, 2012 Report Share Posted April 24, 2012 why cant you just hit up DC for a new knob? thats what i did for my AQ knob when the power light went out on it. Link to comment Share on other sites More sharing options...
Cardboardcat15 Posted April 24, 2012 Author Report Share Posted April 24, 2012 why cant you just hit up DC for a new knob? thats what i did for my AQ knob when the power light went out on it. I didn't buy direct from DC, got it off someone from CACO. Plus, I'm not sure if it's the knob or not. I've seen other threads/videos of people having same issue with the clip light always on with 2k's and 5k's. I'll probably just pick up an LC-1. My Channel on YouTube. Check it out for cinematic-style Car Audio videos. https://www.youtube.com/channel/UCcSMhtT-rpopJbdybubDgnQ New 2014 Scion TC 4th Wall Build https://www.stevemeadedesigns.com/board/topic/217173-2014-tc-4th-order-build-3-fi-sp4-15s/ Link to comment Share on other sites More sharing options...
Cardboardcat15 Posted April 26, 2012 Author Report Share Posted April 26, 2012 K, a little more done. Measured up and cut my false floor. Turns out I have to actually make the floor itself bigger than the dimensions on the box if I want to anchor it through the seat belt bolts. If you can understand what I'm saying, I pretty much have the max dimensions of the box, but the floor itself is larger than those dimensions in order to bolt it down. My depth and width for the BOX are 38x21, but the false floor is actually 43x23. Here are some pictures. Design Completely cut. Someone wanted to help Filling the gaps, started with a simple cardboard template Drawn out on the birch. Ok, Here is where I could use some advice. Should I A: Keep these supports with the height the are (they will be bolted from the side onto the wheel well via a seatbelt bolt) and just have them raise the false floor off of the contours of my car OR B: Cut about 3/4 of an inch off the top of the supports and have them keep the false floor in contact with the bottom of the car. I'll ONLY have these supports bolted in by one seat belt bolt per support, then the false floor on top of that which will also act as the bottom of my box. I'll have the box also secured via the rear deck. What do you guys think, any suggestions? I've got quite a bit of extra space seeing as how each sub only needs 2.0 CF sealed, so I can brace the shit out of this box. My Channel on YouTube. Check it out for cinematic-style Car Audio videos. https://www.youtube.com/channel/UCcSMhtT-rpopJbdybubDgnQ New 2014 Scion TC 4th Wall Build https://www.stevemeadedesigns.com/board/topic/217173-2014-tc-4th-order-build-3-fi-sp4-15s/ Link to comment Share on other sites More sharing options...
Cardboardcat15 Posted April 26, 2012 Author Report Share Posted April 26, 2012 Also, wont be getting much done tomorrow. Going to my buddies graduation, then doin some stuff afterwords. I'll hit it hard this weekend. My Channel on YouTube. Check it out for cinematic-style Car Audio videos. https://www.youtube.com/channel/UCcSMhtT-rpopJbdybubDgnQ New 2014 Scion TC 4th Wall Build https://www.stevemeadedesigns.com/board/topic/217173-2014-tc-4th-order-build-3-fi-sp4-15s/ Link to comment Share on other sites More sharing options...
Cardboardcat15 Posted April 27, 2012 Author Report Share Posted April 27, 2012 Anyone? I want to start this wall already, but I want to do it right. My Channel on YouTube. Check it out for cinematic-style Car Audio videos. https://www.youtube.com/channel/UCcSMhtT-rpopJbdybubDgnQ New 2014 Scion TC 4th Wall Build https://www.stevemeadedesigns.com/board/topic/217173-2014-tc-4th-order-build-3-fi-sp4-15s/ Link to comment Share on other sites More sharing options...
OrionStang Posted April 27, 2012 Report Share Posted April 27, 2012 I say the first one. SMD Super Seller My Feedback Thread Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.