ROBERT 04XBLZ Posted February 3, 2008 Author Report Share Posted February 3, 2008 (edited) at half ohm with stout electrical youd see roughly 4k maybe a little less. so go from there and thats with just one saz-3000 correct? how much do they cost? Edited February 3, 2008 by ROBERT 04XBLZ Quote My New Build checklist: (3) 18'' btl fully loaded d2 Link to comment Share on other sites More sharing options...
AI James Posted February 3, 2008 Report Share Posted February 3, 2008 about 800, youd have to find a dealer though, they may be able to cut you a deal for less, but there isnt any in stock at this time so youd have to find a used one Quote Link to comment Share on other sites More sharing options...
ROBERT 04XBLZ Posted February 3, 2008 Author Report Share Posted February 3, 2008 ok i just checked them out briefly and it says that its Linkable to another SAZ-3000D for up to 6000 watts @ 2 ohms so this setup would be good then. i can wire at two ohms just like my speakers would be and also go down to .5ohm... i think im starting to get it haha 3000 x 1 watts @ 1 ohm 1600 x 1 watts @ 2 ohms 800 x 1 watts @ 4 ohms 0.2v - 6v adjustable input sensitivity 10 Hz - 350 Hz Frequency Response >90 dB S/N Ratio 4-Way Protection Circuit (Thermal, Overload, Speaker Short, and Over Current) Linkable to another SAZ-3000D for up to 6000 watts @ 2 ohms 35 Hz - 300 Hz adjustable 24dB Low-Pass Crossover 10 Hz - 60 Hz adjustable 24dB Subsonic Filter 0 - 180 degree adjustable phase shift 0 - 18 dB adjustable bass boost with 45 Hz center frequency Wired Remote Control unit included 300-amp external fuse required (not included) 23.4" L x 9.9" W x 2" H $1099 US Dollars - MSRP Quote My New Build checklist: (3) 18'' btl fully loaded d2 Link to comment Share on other sites More sharing options...
ROBERT 04XBLZ Posted February 3, 2008 Author Report Share Posted February 3, 2008 (edited) sorry i posted the same thing twice by accident\.. Edited February 3, 2008 by ROBERT 04XBLZ Quote My New Build checklist: (3) 18'' btl fully loaded d2 Link to comment Share on other sites More sharing options...
AI James Posted February 3, 2008 Report Share Posted February 3, 2008 if you already have D2's you could run each one on a single amp or both on 1 but again its pretty pricey and how much is the t3k you were looking at Quote Link to comment Share on other sites More sharing options...
ROBERT 04XBLZ Posted February 3, 2008 Author Report Share Posted February 3, 2008 about 800, youd have to find a dealer though, they may be able to cut you a deal for less, but there isnt any in stock at this time so youd have to find a used one what do you mean that there isnt any in stock everyone is out of stock or something?? Quote My New Build checklist: (3) 18'' btl fully loaded d2 Link to comment Share on other sites More sharing options...
Derrick824 Posted February 3, 2008 Report Share Posted February 3, 2008 You could start with one @ 0.5ohm for around 4,000watts total then add another later. 6,000watts is what they're rated but I believe in the actual strapped test they made closer to 7,000watts. Quote Link to comment Share on other sites More sharing options...
ROBERT 04XBLZ Posted February 3, 2008 Author Report Share Posted February 3, 2008 if you already have D2's you could run each one on a single amp or both on 1 but again its pretty pricey and how much is the t3k you were looking at i believe it was like 700-800. so for the price of the saz-3000 i would be getting almost the same amount as a t4k for half the price almost. Quote My New Build checklist: (3) 18'' btl fully loaded d2 Link to comment Share on other sites More sharing options...
AI James Posted February 3, 2008 Report Share Posted February 3, 2008 what do you mean that there isnt any in stock everyone is out of stock or something?? what it means is all of them are sold from the manufacture at the moment until the next batch is made Quote Link to comment Share on other sites More sharing options...
ROBERT 04XBLZ Posted February 3, 2008 Author Report Share Posted February 3, 2008 You could start with one @ 0.5ohm for around 4,000watts total then add another later. 6,000watts is what they're rated but I believe in the actual strapped test they made closer to 7,000watts. so the numbers are max and not rms? Quote My New Build checklist: (3) 18'' btl fully loaded d2 Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.