Bossmaan

let me get my indash installed and my bass remote (if i do decide to go through all the work of ripping the center console) installed..and I shall post pics.. I took out my 4 channel at the moment, my store might be getting a better model..or I might get the t8004 off a person I know..so im gonna re-do that later..but for now..its just a mono amp..but pics will be up soon

I just took the car into my stores install bay..redid a lot of stuff..got my sub doing parallel now the proper way , and tuned my amp using a MM..holy mother fuckin snakes on a plane..i been underpowering my sub for months I had the gain so low because I was scared to wreck it..I tuned the amp using a 50hz tune at -3db..then played my regular hop music... LOVED THE OUTPUT :^ got my bass control goin too,but that's gonna be hidden soon one more thing...I tuned my amp with using sub lvl +6..because I figured I want that setting anyway with eq flat and loudness OFF..so my gain won't be AS high and as long as i'm not over the rated voltage i'm good to go..correcT?

:-[ let's not point out the obvious now..i was tired from work..been up seen 5 am :'( :^

thx emp, I read your post earlier on, I have my gain set (still need to use a MM tho), I did it by ear.., and now I can use the boost controller knowing that it wont cause clipping if my gain is set right..i just wanted to clear up the whole issue,...and to your reponse from the other thread: I have 4agw wire running all around..I don't have the "Big 3" done, because people are askin for too much money ($150)..I have 4awg goin from the bat to the amps..using a 150amp anl fuse..i got a p6001bd and a p450.4 the mono powers the t1, the 450 powers my 3.5 mid range on dash, 6.5 components, and 6x9 4-ways in the back (all RF)..your explanation cleared up quite a lot for me..my t1 has all 4 coils connected to the box, and outside the box, I have these metal pins joining the two positives, and the two negatives..and 4 wires going into the amp obviously..the wire insdie the sub is 12awg, and same with sub to amp...(should I change the wiring? the installer said using the metal clips, im able to do 2ohms, since im connecting to the polarities) Now it's just a few tweaks here and there and everything should be fine..my sub does pound quite a bit, ..but thanks for clearing up the bass boost...Plus im gonna run the controller wire to my center console near the gear shift, I have a lil flip out cover that covers the cigarette lighter and the ash tray..gonna take the ash tray out, mount the bass boost controller to the flip over it self, so when it flips out, i got my bass boost rdy to go lol it's a lil funky, but hey and wth is a "burr brown d/a convert." sorry :V

wats your ebay reserve, plus shipping to toronto?

meh I guess he's talkin about those effect thingies..i assumed he wanted some screen saver of some sort :-[ sorry!

cause I can't make it go boom boom :'(, because I honestly think it has a ton of potential and I'm not running it properly, and I'm scared of blowing it..and the stupid p6001BD isnt suffient enough for it..or is it?... both amp and sub do 600 at 2ohms...i dunno :-[

I'm not sure if there's a way to do that..what you can do is, get a parking brake by-pass, so you can watch music videos while driving..solves your whole "visuals" thing..but be warned that it is a hazard while you drive..cause if a girl is shakin that ass on that video and ur drooling over it..problems ya know?...plus some units are a bit more different to bypass so it may void the warranty...other than that, watch the road and enjoy ur music

the remote bass thingy? I'm afraid to use it...lol I'm very paranoid after reading so many different forums. :-[..i have my freq set at 40hz on the amp and my h/u is at -12db/oct with 50hz freq... I use to blast my shit like an idiot, and recently i've learned so much and since then i've found so many mistakes; it's just that like i've said, there arent many audio fanatics in toronto, so I havent heard that many high end subs :V but say I set the gains according to the MM with sub level to +6 (no loudness, eq will be flat, SLA level at 0 (need help here, wtf is the deal with this)), and I use the punch bass knob to increase the bass on certain songs...won't that cause clipping? and while setting gain, would using a 45hz be more optimal if i'm planning to use the knob, or stick to 50hz...oh by the way..it'll be 50hz at -3db

what's your shipping price to Toronto Canada... I need the amp to power a T112D4, my p6001 doesnt seem to be powering it properly

wish I had spent that extra money when I purchased my T1 and just upgrade to the 9500, all I hear is good stuff about MTX's 9500..my poor lil t1 isnt even discussed anywhere... :'( doesnt mean i can't do it now..but that means i gotta sell my t1, power enclosure, and the p6001bd...any takers?

thx a bunch meade :^ I exchanged the N2 for the Kenwood 617 (got parkin bypass without soldering and voiding warranty)... I eventually will start getting into (slowly) into a bigger league, but for now it's all I can afford while paying tuition...I feel my p6001bd isnt enough for my t1..I don't use loudness on my deck(obvious reasons) and i find that I gotta set my gain past 2/4 to get my sub to start pounding..i havent done it with a MM yet, so I will be looking into that soon. Sub is wired down to 2ohms and Im just wondering why do I gotta sky rocket my gain to pound my sub..(i dont leave the gain there, i have it much less because I'm afraid to blow my sub) oh and my pioneer is still installed, havent put in the kenwood unit yet...

Hey guys...i recently bought a Pionner N2 dvd unit.. and I also own a pioneer p8600 unit...now the n2 pushes out 2v and the 8600 does 4v.. if i was to install the n2 unit..how much sound quality (in music) would I really by comprimising?... I am currently running a p6001bd (powering a T112d4) and p4004..will my amps have to work harder in anyway / how much clarity / power will I be loosing or gaining...now I know DVD audio has generally better noise ratio...anything else you guys can fill me on?

^x2..you're only 17 bud, building a system to high end shit takes time..especially if ur a student and working. I work part time and am a 3rd yr accounting student...i barely have time to make enuf money and work..my system took a year to complete..and it's not even high end... i got a pioneer 8600, a T112D4, power enclosure, p6001 amp, p4004amp, 6.5 rockford components, rockford 4way 6x9s, tweets, stinger cap kit, wiring and all that bullshit.. this is cheap stuff..i got punch shit in my car ffs...you gotta set your priorities first and work that hobby slowly...

download the Thx - 3 types of bass...makes them subs go sounds :^

pioneer deh8600 love it im just debating if I should attach the Audiocontrol Matrix it to it..