KnockinthaStreetzof608

selenim st200s are pretty much the same tweeter bro just couple minor changes of course run those instead

Thanks! See you in Indiana hopefully?

So I don't turn on the 10x button on my 100.4d? And turn it all the way up??

Bump

I want that 1/0 tech flex all of it to 53511

bump... Nobody knows??? I'm sure I don't have a defective cc-1 I mean it could happen but I find it very unlikely since they hand test every single one, what could be the issue im having, I don't want to throw it away or waste more money and a different product to adjust my crossovers

I have some cheap ones, pm me on how u going give im not looking for much of a profit as long as im not loosing money its urs

no, that's incorrect in what im trying to say I follow all the steps I believe up to maybe 8? Where it says turn headunit volume up until it has a green signal light because if it's red that's to much and I have to lower it, so I did that but it tells you, that your amp has to be on full pass when you are doing this everything from that point works 100% then it says turn to lpf and press read and start calibrating, well my issue is when I flip the switch to lpf the signal light turns back off so now I can't tune it

I have no reason to use the hpf setting on the amp I have 4 mids to two sets bridged on each channel, I haven't touched the hpf since I bought it and it the correct tone its on track 22 which is 5,000hz test tone I mean all goes fine it read signal in a green light but once I flip it to log the signal light goes away and I try to turn up the hi volume to unclipped Max and still nothing

I have done that

Well I tried to calibrate my low pass filter, i follow every step that the manual said but once i change the switch on my sundown 100.4 from full pass to lpf the signal light turns off, and when i keep it on full nd click read it says on turning down but i do and it does not change what's so ever, any idea on things im not doing incorrectly?

zap a gap medium ca+ glue think it's good enough?? To put the dustcap back on?

because nobody was specific on type of glue I have some left over on a recone I will use it thanks nate

Bump u think goop from menards is fine? Or maybe some type of super glue

What kind?? And I just hooked it up and it sounds kinda springy like idk hard to explain, kinda like I can hear coil?? I mean I tuned it correctly subsonic is at 71z and lpf at 5,000

Well while I was mounting my 8s I noticed on of them the dustcap is lose what solution do u have to place it back

sorry im mobile it was typo I do want the pair lol,

One me the shipping on these to 53511 my girl needs alil extra bump in her new car

Never knew u were even a member of smd forum??? Lol but looks good the stuff u do, can tell u guys are pretty much sq guys

I want 4 12inch XL woofers with carbon fibercaps 3stiff spiders 1 medium spider

Knockinthastreetzof608 Beloit Wisconsin I have cc-1 as well idk if u going add that to the list??? And also going have a dual sensor termlab in about a month Free unless I meet u else where then I charge for gas and demo lol

Well I plan on using the 2 channel just for my supertweeters and the 4 channel just for my sundown mids I'm running 2 mid and 1 tweet per door of my mustang no rear fill so what i though i was going do was use the fronts of my alpine use that for the inputs of my 2 channel and the ouputs for the y splitters and use the top output for channel 1nd2 and the bottom output for channel 3nd4 of my 100.4 but that seems wrong now

Ahhh thanks that make sense man thanks just one more question so once I do that does it matter what RCA channel goes with what??? Like for example does RCA channel 1&2 go on the channel 1 of the output of the 125.2 and channel 3&4 to the channel 2 of the 125.2?? Does that make sense??

Bump please help, is it maybe some kind of y splitters?? Or some kind of strapping can be done so I use both sundown amps

Okay well im plan on running a sundown 100.4 and a sundown 125.2 now the question how do I add the RCA on the amps?? Since my headunit (alpine cda 9815) only has 2 RCA for front 2 for rears(planing on removing rear fill no use for it imo) and 2 for woofers so how would I do this? All the mids and highs for the setup will be just on the doors and maybe future a pillar or kicks but never the rear, but have any idea on how to do this??