Jump to content

sierra mist

Members
 View Profile  See their activity

  • Posts

    818

  • Joined

  • Last visited

 Content Type 

Everything posted by sierra mist

  1. sierra mist
    Steve, I need to clean up the amp rack(read MDF board) in my 04 Escalade. Is his amp rack bolted to those seat rods? I'd like to build an amp rack like this. Thank you guys for sharing. I wouldn't think doable without this post.
  2. sierra mist
    x2
  3. sierra mist
    Any reason these are discontinued. Also, what are they being replaced with? I see you guys still have the dual 2 ohm version, but it's OOS.
  4. sierra mist
    I just purchased the app. Could an addition be made for a sealed box designer? I'm sure most folks go ported, but I think having that would be awesome.
  5. sierra mist
    SLT with 4x4 to boot...very nice!
  6. sierra mist
    I hope you get an answer. This is the main reason I'm holding off on getting the 3sixty.3. The video Steve made was for a line driver. From the manual, the 3sixty.3 doesn't have a gain control.
  7. sierra mist
    Does using the 3sixty allow you to avoid using a relay to turn all of the amps on? I did a search on this topic and didn't see anything mentioned about a relay.
  8. sierra mist
    It was a green MEI mosfet amp. I think it was 75x2 RMS. That thing was built like a tank!
  9. sierra mist
    I went back and retested. My sub level goes to 15, not 6. With the level at 15, 33 out of 35 is the highest it will go before the distortion light comes on. When I back it down to 13, I can take the volume up to the max of 35. I'm not sure which one i should go with.
  10. sierra mist
    I just set my sub level to the highest it would go and used the max volume. I still got no distortion.
  11. sierra mist
    I will in a few minutes.
  12. sierra mist
    You make a good point about the sub level. Looks like there are several ways it can be done. I'm sure I will run the sub level over 0 at some point.
  13. sierra mist
    I think I got it now. Here are a couple of pics from when I did the mids/highs amp.
  14. sierra mist
    Got it folks! I have to same feeling as when I first learned to solder. I keep all of my settings on flat. The change came on the HUs xover. I set the front and sub to 200hz(that is as high as it would go). My headunit does not distort at the max volume of 35.
  15. sierra mist
    This is the pic of the HU sub xover. When I press the flat button, it goes back to 80hz.
  16. sierra mist
    I have been trying to mimic the youtube vids. Looks like most folk find the max HU volume with the HU.
  17. sierra mist
    I haven't tried the 1khz yet. Would I need to do that on the full range amp? My equipment is:Alpine INE-S920HD Alpine MRX-M110 Crossfire VR404 Alpline SPS-610S comp set
  18. sierra mist
    I just checked the manual. It's a low pass filter.
  19. sierra mist
    Bass eq on amp is set to 0. Subwoofer level is set to 0 on HU. The HU crossover is set to 80hz. Do I need to change that? Is my HU sub crossover overriding my amp crossover?
  20. sierra mist
    Using the RCA output coming from the HU, it does the same as in the first video. The distortion light will come on before the signal.
  21. sierra mist
    It's the Alpine MRX-M110. There is no switch. I have gain, subsonic filter, LP filter, and bass eq.
  22. sierra mist
    Alright folks, I'm really jazzed that I get to use this tool. I set all my setting flat on the HU. There would have been a vid of that, but there are several menus on the HU. I'm sure I'm making a mistake somewhere. If I need to provide more info, then I will. Thx Vid 1 Vid 2 Vid 3
  23. sierra mist
    Thank you guys so my much. I was running my power wire yesterday. Hopefully, I can get it today.
  24. sierra mist
    Yeah, like the cut it up into a thousand pieces. I know every truck is different., but I can i wouldn't have to do that with my trunk.
  25. sierra mist
    I want to deaden my trunk when I get home. I keep seeing pics of folks having several stripes of deadener on my trunk. Would that be necessary for me? I really want to get this done.
×
×
  • Create New...