profundus-sanus

yep

did you charge the d3100 before you put it in? voltage could be low because its charging up the battery. something would have to be consuming a fair ammount of electricity for your voltage to just be lower like that. I doubt its a bad connection anywhere though.

did you do that flush mount with a coutout bit? always seen it done with a rabetting bit. looks good!

0db tone is a TON of headroom. on audacity i've never seen anything above 70hz be above -5db i've yet to venture into dubstep however... so who knows with that stuff.

100w @ 4 ohm = 20v what db test tone are you using? i really like that amp! 1/0 reducers and crossover section especially.

as stated with a 270xp you need AT LEAST 4 runs of 1/0(2+ and 2-) i would do 5 (3+ and 2-) plus those chassis grounds you already have. imo power wire is the most often skimped on piece of a build...

you can attempt to simulate cabin gain by inserting the linkiwitz transform. i really only use bassbox pro for bandpasses though

yea man. thats exactly what it looks like. clipping light is lighting up when the voltage reaches a certain point. Since the deck was obviously clippin and the light was not conastantly lit*. no way it could actually be measuring any form of distortion. good stuff! at least jbl is trying haha. keep people from just runnning the gain maxxed out... although a -15db track is kinda on the sketchy side

yes!!!! can't wait for a dd1 I can actually use haha. oh damn, i wasn't sure what type of reception it would get but there should be a few that will love it. I will tell you what, the HV will be like $15.00 more but i will waive that fee if you buy one and make you the first to own one....just post a few pics and give an HONEST review. We are confident the review will be good so i say that with confidence. should be ready in about a week. thanks! yea man. An aq20 @ 15.5v input toasted our regular dd1. You actually have it for repair right now. I knew I was right at the limit so i was watching the output voltage like a hawk. I loved the thing man, so it'll be great having one i wont have to worry about when i'm firing up these ns-1's at 18.5volts.

yes!!!! can't wait for a dd1 I can actually use haha.

for the most part we run sundown.

so, completely serious. who's got info about these subs? ssa sells em but looks like they still have specs for the old version.

must quote more quotes. need mad long posts... stat!

Yeah looks like they'll be slapping around everywhere, stitching them to the spider yourself? actually they wont do much slapping, if anything, to me they seem stretched out and could use some slack. with 60mm of linear travel (30mm xmax) I think it could rip them and or cause slap. does it have the little cushions on the cone like some drivers do with leads like that? other than that its a very good looking driver, the crinkle coat looks good and the blacked out plates. Looks like zcon with a bigger bumped bottom plate. What's a rough guesstimate on weight? i will let the engineers at AA worry about if it is going to do damage or if it needs the little cushions. Oh, and sorry but the zcon looks like the Havoc not the other way around. damn man, drinkin that haterade its true, how is that hating? And whats your problem? Nevermind, don't answer that. I already know what it is....speaking of haterade. LOL the man just asked a question.... he asked if there were pads on there. and i just said i would let the engineers decide if they needed pads. I just got the f#ckin things, i dont have the answers yet. Are you done now? smh i seriously don't see what your getting upset about. the guy had a legit question about the woofers. Its kinda hard to tell if there are pads on the back of the cone or not.

kyle you can see the pads in these pics.. kinda hard to distinguish from the cone but they're there.