ChevyBoy Posted February 14, 2007 Report Share Posted February 14, 2007 i would just use a 200 in the front and a 200 in the back and call it done. Link to comment Share on other sites More sharing options...
Coolwazabi Posted February 14, 2007 Report Share Posted February 14, 2007 i would just use a 200 in the front and a 200 in the back and call it done. k Link to comment Share on other sites More sharing options...
95pimpalass Posted July 21, 2007 Report Share Posted July 21, 2007 My ca2600 ALMANI amp uses 3 30 amp fuses would it be ok to use 40 amp fuses or so?? Link to comment Share on other sites More sharing options...
getmoney Posted July 23, 2007 Report Share Posted July 23, 2007 ok i thought it would be best to ask this question here. I have a 900 watts rms amp and all 1/0 gauge wire. the power wire is 20 feet long and the ground is 18 inches . what amp fuse would i need to buy? Link to comment Share on other sites More sharing options...
bassINyoFACE Posted July 23, 2007 Report Share Posted July 23, 2007 125a should be fine I got banned for being an ignorant ass....and im a dickhole i like men, michael jackson and large sausages Link to comment Share on other sites More sharing options...
getmoney Posted July 23, 2007 Report Share Posted July 23, 2007 125a should be fineso when i add the second amp i should get a 250a fuse right?(the second amp is the same) Link to comment Share on other sites More sharing options...
andym85 Posted July 23, 2007 Report Share Posted July 23, 2007 My ca2600 ALMANI amp uses 3 30 amp fuses would it be ok to use 40 amp fuses or so??i would stick with 30amp fuses to be safe. they are ment to blow with a certain amount of current draw...so if by chance your amp drew the full 90amps but you had three 40amp fuses in (120amps) then you may damage your amp. ok i thought it would be best to ask this question here. I have a 900 watts rms amp and all 1/0 gauge wire. the power wire is 20 feet long and the ground is 18 inches . what amp fuse would i need to buy? the largest size would be the fuse rating for 1/0gauge wire, the smallest i would say would be to match the fuse size to whatever the fuses are on the amp (assuming the amps is fuses). so if you have 3 40 amp fuses on your amp, the fuse the power wire with a 120amp fuse. i likes me some audio stuff... Link to comment Share on other sites More sharing options...
Chris Posted July 23, 2007 Report Share Posted July 23, 2007 i would stick with 30amp fuses to be safe. they are ment to blow with a certain amount of current draw...so if by chance your amp drew the full 90amps but you had three 40amp fuses in (120amps) then you may damage your amp. the largest size would be the fuse rating for 1/0gauge wire, the smallest i would say would be to match the fuse size to whatever the fuses are on the amp (assuming the amps is fuses). so if you have 3 40 amp fuses on your amp, the fuse the power wire with a 120amp fuse. With a run of 1/0gauge, I'd just slap a fat 300amp fuse in there. Might be a lil less resistance then overall. Definately stick with your amp's rated fuse size though for in the amp itself. 4 15" FI Q D2's in 12 cubes tuned to 32hz 1- T1000.1bd's 3 Maxx 29 deep cycles 4 runs of 1/0 gauge -Big 3 -Trunk sealed off from the cabin Custom 15.8 dual-volt switching MLA module All in a CAR. Link to comment Share on other sites More sharing options...
andym85 Posted July 23, 2007 Report Share Posted July 23, 2007 With a run of 1/0gauge, I'd just slap a fat 300amp fuse in there. Might be a lil less resistance then overall. Definately stick with your amp's rated fuse size though for in the amp itself. i would do the same...i was just giving a rough range for him though i likes me some audio stuff... Link to comment Share on other sites More sharing options...
getmoney Posted July 23, 2007 Report Share Posted July 23, 2007 i would stick with 30amp fuses to be safe. they are ment to blow with a certain amount of current draw...so if by chance your amp drew the full 90amps but you had three 40amp fuses in (120amps) then you may damage your amp. the largest size would be the fuse rating for 1/0gauge wire, the smallest i would say would be to match the fuse size to whatever the fuses are on the amp (assuming the amps is fuses). so if you have 3 40 amp fuses on your amp, the fuse the power wire with a 120amp fuse. so in the event of a shortage i would be safe? cause i really dont care about the amps i just dont want the truck to burn up. so i guess i will just use a 125A fuse. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.