numatik Posted June 9, 2011 Report Share Posted June 9, 2011 You have nice welds man, mad props for the patience to do all those welds with a 110v and a torch thanks bro, haha surprisingly only takes extra 5 or so mins with torch to get it hot enough to accept weld and the funny thing is my welder isnt even at full potential because i have a 10 amp breaker and welder needs 15 to get max power i wish i had more shit to weld up to practice my welds but that there was me not touching welder in couple weeks and just trying different techniques n shit but it turned out well Start building minitrucks. I have so much metal everywhere, scraps from all different stages of the build, and iv never throw away a piece of metal in my life. Somewhere local you could probably find a shop that considers it junk and throws it in big bins stashed around the shop. they would love if you came and took it, you should ask around. You do need to get a bigger breaker tho bro, on that low of power those welds cant be biting as hard you kno? another good way to get more penetration is making a larger ground clamp. on my 110v I had a 2/0awg Fosgate clamp . In your garage upping a 10a to 15a breaker should be fine with the existing wiring but no higher Gary 'Numatik' Eberle West Sacramento, California Vehicle build log (1) 'Aayla' Numatik's one and only, bodydropped pasted the doors Chevy S-20 Ext-Ext cab. This project ended after a horrible horrible motorcycle accident. There are so many mods it would fill an entire page in my sig. Check it out if you have A LOT of time to kill. http://www.stevemeadedesigns.com/board/topic/39785-numatiks-doored-s-20-bodydropped-on-doors-ext-ext-cab-10-subs-full-frame-build/?hl=%20numatik#39;s Vehicle build log (2) 'Snow White' Daily/showstopper 2004 Chevy Silverado Lays on 22s soon for 26s to run a beefy tire on 4s (4) 5gal tanks, (3)AZOB2 pumps, Slam digital stealth two speed valves with 16 solenoids, Slam SS bags all around, ART upper and lower arms, KP Components 6-link, KP Components watts link, Panther juice 6 22s, Spikes EVERYWHERE. 3,600WRMS total, (5) Kicker amps, (2) L7 15s under raised back seats, 15" screen molded to dash, 36 speakers total all Mb Quartz and Fosgate. Fiberglass console with removable face plates and arm rests, flushed speakers, lots of toggle switches, Playstation 2, rear view camera, Suede and leather seats, suede headliner, Dakota Digital air gauges, voltage gauges, and current draw gauges. (2) XS Power 4800 batteries, Whole truck is flat black and white and the ENTIRE truck is fully pin striped by TJ Pagano here in Sacramento. http://www.stevemeadedesigns.com/board/topic/123328-numatiks-bagged-2004-silverado/ "What doesn't kill you makes you stronger. I am proof" - Numatik Link to comment Share on other sites More sharing options...
uhoh_45 Posted June 9, 2011 Author Report Share Posted June 9, 2011 You have nice welds man, mad props for the patience to do all those welds with a 110v and a torch thanks bro, haha surprisingly only takes extra 5 or so mins with torch to get it hot enough to accept weld and the funny thing is my welder isnt even at full potential because i have a 10 amp breaker and welder needs 15 to get max power i wish i had more shit to weld up to practice my welds but that there was me not touching welder in couple weeks and just trying different techniques n shit but it turned out well Start building minitrucks. I have so much metal everywhere, scraps from all different stages of the build, and iv never throw away a piece of metal in my life. Somewhere local you could probably find a shop that considers it junk and throws it in big bins stashed around the shop. they would love if you came and took it, you should ask around. You do need to get a bigger breaker tho bro, on that low of power those welds cant be biting as hard you kno? another good way to get more penetration is making a larger ground clamp. on my 110v I had a 2/0awg Fosgate clamp . In your garage upping a 10a to 15a breaker should be fine with the existing wiring but no higher i wish i could build mini trucks but no one wants to do it haha i am going to wall off the lumina with 4 15s and 10k power welded frame into vehicle so need practice for that i go to my brother every once and a while for some steel and yeah i know its not full pen but its good enough for what i need shit with my moped is simple simple work and the occasional weld for speaker box or something im just a hobbyist haha but i will look into my brothers shop for some steel to grab and play with and i need to install a new breaker in the garage so i can have dedicated welding line R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log Link to comment Share on other sites More sharing options...
numatik Posted June 9, 2011 Report Share Posted June 9, 2011 You have nice welds man, mad props for the patience to do all those welds with a 110v and a torch thanks bro, haha surprisingly only takes extra 5 or so mins with torch to get it hot enough to accept weld and the funny thing is my welder isnt even at full potential because i have a 10 amp breaker and welder needs 15 to get max power i wish i had more shit to weld up to practice my welds but that there was me not touching welder in couple weeks and just trying different techniques n shit but it turned out well Start building minitrucks. I have so much metal everywhere, scraps from all different stages of the build, and iv never throw away a piece of metal in my life. Somewhere local you could probably find a shop that considers it junk and throws it in big bins stashed around the shop. they would love if you came and took it, you should ask around. You do need to get a bigger breaker tho bro, on that low of power those welds cant be biting as hard you kno? another good way to get more penetration is making a larger ground clamp. on my 110v I had a 2/0awg Fosgate clamp . In your garage upping a 10a to 15a breaker should be fine with the existing wiring but no higher i wish i could build mini trucks but no one wants to do it haha i am going to wall off the lumina with 4 15s and 10k power welded frame into vehicle so need practice for that i go to my brother every once and a while for some steel and yeah i know its not full pen but its good enough for what i need shit with my moped is simple simple work and the occasional weld for speaker box or something im just a hobbyist haha but i will look into my brothers shop for some steel to grab and play with and i need to install a new breaker in the garage so i can have dedicated welding line Anybody can build minitrucks, but it just takes time, money, drive, trial and error, and alot of it for all stated. il def follow the build of 4 15s in the lumina, that sounds bad ass! when you start it shoot me the link to your thread! thats awesome even for hobby welding, because its a trait thats just good to have in your lifetime because things will always come up that require it installing a breaker is a bitch. I was gonna do 3 lines of 220 and a separate breaker box in the garage and it was gonna be like 4 grand. Im sure I could learn it but just havnt had time to do it, or money for supplys cause my money goes into the s20. Gary 'Numatik' Eberle West Sacramento, California Vehicle build log (1) 'Aayla' Numatik's one and only, bodydropped pasted the doors Chevy S-20 Ext-Ext cab. This project ended after a horrible horrible motorcycle accident. There are so many mods it would fill an entire page in my sig. Check it out if you have A LOT of time to kill. http://www.stevemeadedesigns.com/board/topic/39785-numatiks-doored-s-20-bodydropped-on-doors-ext-ext-cab-10-subs-full-frame-build/?hl=%20numatik#39;s Vehicle build log (2) 'Snow White' Daily/showstopper 2004 Chevy Silverado Lays on 22s soon for 26s to run a beefy tire on 4s (4) 5gal tanks, (3)AZOB2 pumps, Slam digital stealth two speed valves with 16 solenoids, Slam SS bags all around, ART upper and lower arms, KP Components 6-link, KP Components watts link, Panther juice 6 22s, Spikes EVERYWHERE. 3,600WRMS total, (5) Kicker amps, (2) L7 15s under raised back seats, 15" screen molded to dash, 36 speakers total all Mb Quartz and Fosgate. Fiberglass console with removable face plates and arm rests, flushed speakers, lots of toggle switches, Playstation 2, rear view camera, Suede and leather seats, suede headliner, Dakota Digital air gauges, voltage gauges, and current draw gauges. (2) XS Power 4800 batteries, Whole truck is flat black and white and the ENTIRE truck is fully pin striped by TJ Pagano here in Sacramento. http://www.stevemeadedesigns.com/board/topic/123328-numatiks-bagged-2004-silverado/ "What doesn't kill you makes you stronger. I am proof" - Numatik Link to comment Share on other sites More sharing options...
uhoh_45 Posted June 10, 2011 Author Report Share Posted June 10, 2011 You have nice welds man, mad props for the patience to do all those welds with a 110v and a torch thanks bro, haha surprisingly only takes extra 5 or so mins with torch to get it hot enough to accept weld and the funny thing is my welder isnt even at full potential because i have a 10 amp breaker and welder needs 15 to get max power i wish i had more shit to weld up to practice my welds but that there was me not touching welder in couple weeks and just trying different techniques n shit but it turned out well Start building minitrucks. I have so much metal everywhere, scraps from all different stages of the build, and iv never throw away a piece of metal in my life. Somewhere local you could probably find a shop that considers it junk and throws it in big bins stashed around the shop. they would love if you came and took it, you should ask around. You do need to get a bigger breaker tho bro, on that low of power those welds cant be biting as hard you kno? another good way to get more penetration is making a larger ground clamp. on my 110v I had a 2/0awg Fosgate clamp . In your garage upping a 10a to 15a breaker should be fine with the existing wiring but no higher i wish i could build mini trucks but no one wants to do it haha i am going to wall off the lumina with 4 15s and 10k power welded frame into vehicle so need practice for that i go to my brother every once and a while for some steel and yeah i know its not full pen but its good enough for what i need shit with my moped is simple simple work and the occasional weld for speaker box or something im just a hobbyist haha but i will look into my brothers shop for some steel to grab and play with and i need to install a new breaker in the garage so i can have dedicated welding line Anybody can build minitrucks, but it just takes time, money, drive, trial and error, and alot of it for all stated. il def follow the build of 4 15s in the lumina, that sounds bad ass! when you start it shoot me the link to your thread! thats awesome even for hobby welding, because its a trait thats just good to have in your lifetime because things will always come up that require it installing a breaker is a bitch. I was gonna do 3 lines of 220 and a separate breaker box in the garage and it was gonna be like 4 grand. Im sure I could learn it but just havnt had time to do it, or money for supplys cause my money goes into the s20. if im doing anything to a truck its a blow or walk trough so wont need the welder all that much haha and the lumina is starting when dave gets new vehicle sometime this summer but i will shoot you the link ans yeah i plan on becoming a welder for a career but needs go school first haha i love being able to create shit and really 4 grand damn i know my basic electrical so it shouldnt be to big of strain to put new breaker in garage plus i know couple electricians so i could ask for help if need be i want to have a strictly welder/high power outlet in the garage for things like welder propane heater drill press when drilling thick shit R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log Link to comment Share on other sites More sharing options...
numatik Posted June 12, 2011 Report Share Posted June 12, 2011 You have nice welds man, mad props for the patience to do all those welds with a 110v and a torch thanks bro, haha surprisingly only takes extra 5 or so mins with torch to get it hot enough to accept weld and the funny thing is my welder isnt even at full potential because i have a 10 amp breaker and welder needs 15 to get max power i wish i had more shit to weld up to practice my welds but that there was me not touching welder in couple weeks and just trying different techniques n shit but it turned out well Start building minitrucks. I have so much metal everywhere, scraps from all different stages of the build, and iv never throw away a piece of metal in my life. Somewhere local you could probably find a shop that considers it junk and throws it in big bins stashed around the shop. they would love if you came and took it, you should ask around. You do need to get a bigger breaker tho bro, on that low of power those welds cant be biting as hard you kno? another good way to get more penetration is making a larger ground clamp. on my 110v I had a 2/0awg Fosgate clamp . In your garage upping a 10a to 15a breaker should be fine with the existing wiring but no higher i wish i could build mini trucks but no one wants to do it haha i am going to wall off the lumina with 4 15s and 10k power welded frame into vehicle so need practice for that i go to my brother every once and a while for some steel and yeah i know its not full pen but its good enough for what i need shit with my moped is simple simple work and the occasional weld for speaker box or something im just a hobbyist haha but i will look into my brothers shop for some steel to grab and play with and i need to install a new breaker in the garage so i can have dedicated welding line Anybody can build minitrucks, but it just takes time, money, drive, trial and error, and alot of it for all stated. il def follow the build of 4 15s in the lumina, that sounds bad ass! when you start it shoot me the link to your thread! thats awesome even for hobby welding, because its a trait thats just good to have in your lifetime because things will always come up that require it installing a breaker is a bitch. I was gonna do 3 lines of 220 and a separate breaker box in the garage and it was gonna be like 4 grand. Im sure I could learn it but just havnt had time to do it, or money for supplys cause my money goes into the s20. if im doing anything to a truck its a blow or walk trough so wont need the welder all that much haha and the lumina is starting when dave gets new vehicle sometime this summer but i will shoot you the link ans yeah i plan on becoming a welder for a career but needs go school first haha i love being able to create shit and really 4 grand damn i know my basic electrical so it shouldnt be to big of strain to put new breaker in garage plus i know couple electricians so i could ask for help if need be i want to have a strictly welder/high power outlet in the garage for things like welder propane heater drill press when drilling thick shit i hear ya, il prolly be doing a blowthru in my daily soon but yea ul be all set if you kno a electrical dude, and good luck with the school, thatd be a kickass career :good: Gary 'Numatik' Eberle West Sacramento, California Vehicle build log (1) 'Aayla' Numatik's one and only, bodydropped pasted the doors Chevy S-20 Ext-Ext cab. This project ended after a horrible horrible motorcycle accident. There are so many mods it would fill an entire page in my sig. Check it out if you have A LOT of time to kill. http://www.stevemeadedesigns.com/board/topic/39785-numatiks-doored-s-20-bodydropped-on-doors-ext-ext-cab-10-subs-full-frame-build/?hl=%20numatik#39;s Vehicle build log (2) 'Snow White' Daily/showstopper 2004 Chevy Silverado Lays on 22s soon for 26s to run a beefy tire on 4s (4) 5gal tanks, (3)AZOB2 pumps, Slam digital stealth two speed valves with 16 solenoids, Slam SS bags all around, ART upper and lower arms, KP Components 6-link, KP Components watts link, Panther juice 6 22s, Spikes EVERYWHERE. 3,600WRMS total, (5) Kicker amps, (2) L7 15s under raised back seats, 15" screen molded to dash, 36 speakers total all Mb Quartz and Fosgate. Fiberglass console with removable face plates and arm rests, flushed speakers, lots of toggle switches, Playstation 2, rear view camera, Suede and leather seats, suede headliner, Dakota Digital air gauges, voltage gauges, and current draw gauges. (2) XS Power 4800 batteries, Whole truck is flat black and white and the ENTIRE truck is fully pin striped by TJ Pagano here in Sacramento. http://www.stevemeadedesigns.com/board/topic/123328-numatiks-bagged-2004-silverado/ "What doesn't kill you makes you stronger. I am proof" - Numatik Link to comment Share on other sites More sharing options...
uhoh_45 Posted June 23, 2011 Author Report Share Posted June 23, 2011 made little fishing rod holder for using a pickerel rig used some fence post and some of the "bastard bars" from trunk of lumina R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log Link to comment Share on other sites More sharing options...
uhoh_45 Posted July 2, 2011 Author Report Share Posted July 2, 2011 so i did some lathe work today in the middle of making a peddle extension for moped to clear the exhaust as you can see the peddle doesn't clear the new muffler this is just part that needs to be welded to some 1x1 solid square stock but i need go to brothers shop to use his big welder and drill press so will have updates shortly here R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log Link to comment Share on other sites More sharing options...
uhoh_45 Posted July 3, 2011 Author Report Share Posted July 3, 2011 R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log Link to comment Share on other sites More sharing options...
Rebel4055 Posted July 3, 2011 Report Share Posted July 3, 2011 Looks sick! Rest In Peace mother. January 22, 1955 - February 14, 2013 http://www.stevemeadedesigns.com/board/user/35351-megrch/ Link to comment Share on other sites More sharing options...
uhoh_45 Posted August 12, 2011 Author Report Share Posted August 12, 2011 sweet new sandblaster i got for 35$ at garage sale R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.