flwatersaver Posted December 25, 2011 Report Share Posted December 25, 2011 I sent tony a PM, no point in me posting a video, mine is doing the exact same thing. My amps are dc 3.5k and rockford t400-4. Quote My selling FeedbackBuild log - Blazer C pillar wall, Two DC Audio 3.5k'sTEAM PSI Link to comment Share on other sites More sharing options...
JeremyN Posted December 26, 2011 Report Share Posted December 26, 2011 when I run mine thru my external cross over I get the same thing ....... my external cross over is a Coustic XM-1.... I dont get it Quote 2 12" Jeff Vue Customs 1 set MB Quart FSB 216 in doors1 American Bass 100.1 on sub1 Hertz EP2 on doorsJVC deck IPOD controlStock 105 amp alt DD-1big 3new build in Chevy caviler http://www.stevemead...chevy-cavalier/last set up in the ZX2 http://www.stevemead...-current-build/old build log http://www.stevemead...-1998-ford-zx2/ Gold is the money of kings, silver is the money of gentlemen, debt is the money of slaves. Just my .02c that shop needs keep those doors open so they have to charge for it if people think 10k is a lot then they should get into other hobbies.. like masturbating, cause any hobby cost money to maintain Lol no, I'm smarter than that bro haha. Fool me once, shame on you, fool me twice..............go fuck yourself lol Link to comment Share on other sites More sharing options...
flwatersaver Posted December 27, 2011 Report Share Posted December 27, 2011 (edited) Both done with -0db tracks, full volume on head unit. Off of the RCA cables right before amps. I am looking for a portable scope. I am told the range for being off is +/-0.1 20hz and +/-0.5 at 10khz Edit I found a fluke 863 graphical multimeter Edited December 27, 2011 by flwatersaver Quote My selling FeedbackBuild log - Blazer C pillar wall, Two DC Audio 3.5k'sTEAM PSI Link to comment Share on other sites More sharing options...
TonyD'Amore Posted December 27, 2011 Report Share Posted December 27, 2011 Both done with -0db tracks, full volume on head unit. Off of the RCA cables right before amps. I am looking for a portable scope. I am told the range for being off is +/-0.1 20hz and +/-0.5 at 10khz Edit I found a fluke 863 graphical multimeter So what happens when you leave the headunit connected to the amplifiers and measure with the included harness at the speaker connectors of amplifier and use a -10dB track? Quote Link to comment Share on other sites More sharing options...
flwatersaver Posted December 27, 2011 Report Share Posted December 27, 2011 (edited) Both done with -0db tracks, full volume on head unit. Off of the RCA cables right before amps. I am looking for a portable scope. I am told the range for being off is +/-0.1 20hz and +/-0.5 at 10khz Edit I found a fluke 863 graphical multimeter So what happens when you leave the headunit connected to the amplifiers and measure with the included harness at the speaker connectors of amplifier and use a -10dB track? The same thing CJ18's was doing. I can post a video later if you want? Edited December 27, 2011 by flwatersaver Quote My selling FeedbackBuild log - Blazer C pillar wall, Two DC Audio 3.5k'sTEAM PSI Link to comment Share on other sites More sharing options...
01VWGREENMACHINE Posted December 27, 2011 Report Share Posted December 27, 2011 i been watching this thread for a week or so and if i remember correctly my kenwood x494 did not have this problem but my pioneer avh-4200dvd does. i will try to test in the next couple of days to see ill take video as well Quote http://www.stevemead...f-system-build/ 2001 VW GTI with a 1.8T motor BIG 3 Pioneer AVH-4200DVD DOUBLE DIN HEAD UNIT 6 - 4 VOLT PREOUTS RF T1500-BDCP (running at 2 ohm) RF T400.4 RF T1 D212 x2 (in ported box) RF 1/0 TO 4 GAUGE distribution block x 2 all stinger wires 200a alternator (SINGER ALT) RF T2652-S (6.5 MID BASS AND 1" TWEETS in front and rear) KINETIC HC 800 BATTERY (Front) KINETIC HC 1200 BATTERY (BACK) 120ft of 1/0 stinger blue and clear matt 20ft of 4 gauge stinger blue and clear matt 30ft of 8 gauge stinger blue and clear matt 100ft of 12 gauge stinger speaker wire black Link to comment Share on other sites More sharing options...
TonyD'Amore Posted December 27, 2011 Report Share Posted December 27, 2011 So when you have it connected at amplifier you get signal and distortion LEDs, but no 1kHz or 40Hz LEDs? Quote Link to comment Share on other sites More sharing options...
TonyD'Amore Posted December 27, 2011 Report Share Posted December 27, 2011 when I run mine thru my external cross over I get the same thing ....... my external cross over is a Coustic XM-1.... I dont get it Sounds like your crossover is distorting the signal Quote Link to comment Share on other sites More sharing options...
TonyD'Amore Posted December 27, 2011 Report Share Posted December 27, 2011 (edited) i been watching this thread for a week or so and if i remember correctly my kenwood x494 did not have this problem but my pioneer avh-4200dvd does. i will try to test in the next couple of days to see ill take video as well I have tested a least a dozen headunits that are distorted at 40Hz, from both the RCA outputs and speaker outputs. I have looked at them on a scope and they don't look that bad to the naked eye, but they are very distorted. I wouldn't want a headunit in my system that has this problem. Yes 9.5% THD!! Edited December 27, 2011 by TonyD'Amore Quote Link to comment Share on other sites More sharing options...
flwatersaver Posted December 27, 2011 Report Share Posted December 27, 2011 I tested it with the amp, Please forgive me as I am very tired, I have been on nights for 5 days now and only 4 hrs of sleep per day. http://www.youtube.com/watch?v=Pmf_38VY8ls I am going to go check my brother's pioneer headunit, to see what it does. Quote My selling FeedbackBuild log - Blazer C pillar wall, Two DC Audio 3.5k'sTEAM PSI Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.